#include "global.h"

#if TONG_YONG_MACHINE

void TBJ_InitAction(void);
void TBJ_Action(void);
void CSTB_SongJiao_CS(void);
void CSTB_Auto_Con_CS(void);
void CSTB_HeMo_CS_CS(void);
void Auto_Run(void);
void Hand_Action(void);
unsigned short cCountTime;
unsigned char TBJ_cOneTimes,cTest1;
unsigned long cErrorTime1,cErrorTime2,cErrorTime3;
static long cSetEncode;
static long cEncodePulse;
unsigned char tbj_bRunning = 0,tbj_bStop;
void TBJ_InitAction(void)
{
        XGearRatio  = 1;
	if(CJSelect == XinYe)//鑫业的Y06为夹胶
	{
		if(X17)Y06 = 1;
	}
	SetEn(X_AXIS,1);   //步进电机松	
}

void TBJ_Action(void)
{
                static unsigned long c10msDelay = 0;
		//cStepMByte;
		user_datas[122] = cStepMByte1;
		user_datas[123] = cStepMByte2;
		user_datas[124] = cStepMByte3;
		user_datas[125] = cStepMByte4;
//		user_datas[126] = cStepMByte5;

		CSTB_HeMo_CS_CS();	//合模超声动作
		CSTB_SongJiao_CS();	//送胶动作
		CSTB_Auto_Con_CS();	//电机拖带动作
		if(dwTickCount >= c10msDelay)
		{
                      c10msDelay = dwTickCount+10;
			if(cCountTime > 0)
			{
				cCountTime--;
				if(cCountTime == 0)Y07 = 0;
			}
		}
                
		if(M0015)  //M15 故障确定
		{	
			M0015 = 1;
			user_datas[100] = 0;
			user_datas[75] = 1;
			cDelayTime7 = dwTickCount + (unsigned long)1010;
		}
		if(M0001)	 //清产量
		{
			if(dwTickCount >= cDelayTime8)
			{
				M0001 = 0;
			 ClrcToTal(76);
			}
		}
		else
		{
			cDelayTime8 = dwTickCount + (unsigned long)120*10;
		}
		//设定音波参数使能
		if(M0005)
		{
			if(dwTickCount >= cDelayTime9)
			{
				M0005 = 0; 	
				M0006 = 1; 	
				cDelayTime10 = dwTickCount + (unsigned long)5000;
			}	
		}
		else 
			cDelayTime9 = dwTickCount + (unsigned long)1300;
		if(M0006 && (dwTickCount >= cDelayTime10))
		{
			M0006 = 0; 
		}
		if(CJSelect == ChangSheng)
		{
			if(Y06 && (dwTickCount >= cDelayTime6))
			{
				Y06 = 0;	
			}
		}
		else if(CJSelect == XinYe)
		{
			if(Y11 && (dwTickCount >= cDelayTime6))
			{
				Y11 = 0;	
			}
		}
		//停止
		if(X01 || tbj_bStop || M0014)
		{
			M0019 = 0; 
			M0014 = 0;
			M0015 = 0;
			M0002 = 0;
                        Y00 = 0;
                        Y01 = 0;
                        Y02 = 0;
                        Y03 = 0;
                        Y04 = 0;
                        Y05 = 0;

                        Y15 = 0;
                        Y11 = 0;
                        Y12 = 0;
                        Y13 = 0;
                        Y14 = 0;
                        Y15 = 0;

			cStepMByte = 0;
			cStepMByte1 = 0;
			cStepMByte2 = 0;
			cStepMByte3 = 0;
			cStepMByte4 = 0;
			tbj_bRunning = 0;
			AxisEgmStop(X_AXIS);  
			tbj_bStop = 0;
			SETDR();   //步进电机松	

			cCountTime = user_datas[30] * 100 + 2;		
			TBJ_cOneTimes = 0;
		}
		
		if(((X00 && !OLDX00) || M0000 || M0016) && !X01)
		{
			M0000 = 0;
			 //分胶      送胶       分胶前 分胶后     送胶到位 退胶到位		                     双勾针方式时勾针要退到位　　　　　　　单勾针方式
			//if((!Y02) && (!Y04) && (!X12) && (X13 || FengJiaoSelect) && (((!X16) && X17) || (SongJiaoMode == 1)) && (((SGZSelect == 0) && X15 && !X20) || (SGZSelect == 1)) && !bRunning)
			{
				tbj_bRunning = 1;
				cStepMByte = 1;
				M0002 = 1;//cMidleCoil[0] |= (1<<2);
				user_datas[100] = 0;
				TBJ_cOneTimes = 0;
				cCountTime = 0;
				if(M0016)
				{
					TBJ_cOneTimes = 1;
					M0017 = 1;
					M0002 = 0;
				}
				
                                Y07 = 1;			//计数器输出	
			}
			M0016 = 0;
		}
		//手动模式
		if(!tbj_bRunning && !X01)
		{	 				
			Hand_Action();
		}
		else if(tbj_bRunning)
		{
			Auto_Run();	
		}
		else if(X01)
		{
			Y00 = 0;
			Y01 = 0;
			Y02 = 0;
			Y03 = 0;
			Y04 = 0;
			Y05 = 0;
			if(CJSelect == XinYe)//鑫业的Y06为夹胶
			{
			    if(X17)Y06 = 1;	
			}
			else
			    Y06 = 0;
			Y15 = 0;	
			tbj_bRunning = 0;	
		}
		if(CJSelect != XinYe)
		{
			if(Y15)
				Y11 = 1;
			else
				Y11 = 0;	
		}							
}




void TBStartCuiQi(void)
{
	if(CJSelect == ChangSheng)//鑫业的Y06为夹胶不能输出
		Y06 = 1;	//吹气
	else if(CJSelect == XinYe)
		Y11 = 1;	
	cDelayTime6 = dwTickCount + (unsigned long)10 * user_datas[8];	
}
//电机控制
void CSTB_Auto_Con_CS(void)
{
        unsigned short speed_buf;

        long cWorkPulseNum;
        cEncodePulse = GetPos(X_AXIS);
	switch(cStepMByte2)	
	{
		case 0:
			Y00 = 0;
  			if(X_DRV)AxisEgmStop(X_AXIS);     
			break;
		case 1:    //离合器起动
			cStepMByte2 = 2;
			Y00 = 1;      //离合器输出				
			if(user_datas[90] == 55)
				cDelayTime3 = dwTickCount + (unsigned long)300;
			       
			
			cErrorTime2 = dwTickCount + (unsigned long)100*user_datas[24];			

   
                        if(!X11)
			{
			    if(!X_DRV)MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,user_datas[13],user_datas[10],user_datas[11],2);      
			}
                        else
			    if(!X_DRV)MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,user_datas[12],user_datas[10],user_datas[11],2);      
			break;	
		case 2:    //过链接近下降沿			
			if((!X11) || ((user_datas[90] == 55) && (dwTickCount >= cDelayTime3)))
			{			
				cStepMByte2 = 3;
				if(user_datas[90] == 55)
					cDelayTime3 = dwTickCount + (unsigned long)200;
				else	
					cDelayTime3 = dwTickCount + (unsigned long)5;	
				cErrorTime2 = dwTickCount + (unsigned long)TBJ_ERRORTIME;
				AxisChangeSpeed(X_AXIS,user_datas[13]);				
			}
			else if((dwTickCount>=cErrorTime2) && (user_datas[24] != 0))
			{
				user_datas[75] = ActionPage;
				user_datas[100] = NoZip_W;      	//检查过链接近开关或没有拉链
				M15 = 0;
				tbj_bStop = 1;	
			}
			else if((user_datas[29] > 5) && ((0 - cEncodePulse) >= (cSetEncode + user_datas[29] * 10)) && (cTest1 > 1))
			{
				user_datas[75] = ActionPage;
				user_datas[100] = ZipperLengPRO_W;      	//检查过链接近开关或没有拉链
				M15 = 0;
				tbj_bStop = 1;		
			}
			break;
		case 3:	
			//过链接近上升沿  	//拖带到
			if(((X11_UP) || !Y00 || (user_datas[90] == 55)) && (dwTickCount >= cDelayTime3))
			{
				if(TWOTDSelect == 0)	//普通拖带
				{
					AxisChangeSpeed(X_AXIS,user_datas[13]);	 	//电机减速
					cStepMByte2 = 4;
					cErrorTime2 = dwTickCount + (unsigned long)500;
					cDelayTime3 = dwTickCount + (unsigned long)user_datas[5];
					cDelayTime4 = dwTickCount + (unsigned long)user_datas[1];   // 延时上勾针
				}
				else 
				{	
					cDelayTime3 = dwTickCount + (unsigned long)user_datas[26];
					cStepMByte2 = 40;
				}
			}
			else if(dwTickCount >= cErrorTime2) //拖带警告
			{
				//cMidleCoil[5] |= (1<<0); 	//记录
				user_datas[75] = ActionPage;
				user_datas[100] = NoZip_W;      	//检查过链接近开关或没有拉链
				M15 = 0;//cMidleCoil[0] &= ~(1<<15);  //M15
				tbj_bStop = 1;
			}
			break;
		case 40:
			if(dwTickCount >=  cDelayTime3)
			{
				CLRQ00;					//离合停
				AxisEgmStop(X_AXIS);  				//步进电机停

				if(cStepMByte1 == 0)  	//送胶完成
				{
					SETQ01;    //上勾针
					cDelayTime3 = dwTickCount + (unsigned long)10 * user_datas[25];
					cStepMByte2 = 41;
				}
			}		
			break;		
		case 41:			
			if((dwTickCount >=  cDelayTime3) && !X_DRV)	
			{
				cStepMByte2 = 4;	
				cErrorTime2 = dwTickCount + (unsigned long)500;
				cDelayTime3 = dwTickCount + (unsigned long)user_datas[5];
				MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,user_datas[13],user_datas[10],user_datas[11],2); 
				SETQ00;		//离合开
			}
			break;	
		case 4:
			//要加延时上勾针
			if(dwTickCount >= cDelayTime4)
				SETQ01;    //上勾针
			if(((dwTickCount >= cDelayTime3) && (SGZSelect != 0)) || (X20 ||(user_datas[90] == 55)))  //到位或延时停时间到
			{
				SETQ01;    //上勾针
				CLRQ00;		//离合停
				AxisEgmStop(X_AXIS);  		//步进电机停
				if(SGZSelect == 0)   //双勾针
				{
					cStepMByte2 = 5;	
					cDelayTime3 = dwTickCount + (unsigned long)1;		//延时压带
				}
				else		//单勾针
				{
					cStepMByte2 = 0;
                                        cDelayTime5 = dwTickCount + 50;
					//SETDR();   //步进电机松	
				}	
			}
			else if((dwTickCount >= cErrorTime2) && (SGZSelect == 0)) //拖带警告
			{
				
				user_datas[75] = ActionPage;
				user_datas[100] = GZDaoWei_W;      	//检查过链接近开关或没有拉链
				M15 = 0;//cMidleCoil[0] &= ~(1<<15);  //M15
				tbj_bStop = 1;
			}
			break;
		case 5:
			if((dwTickCount >= cDelayTime3) && !X_DRV)
			{
				cStepMByte2 = 6;  
				SETQ05;
				cDelayTime3 = dwTickCount + (unsigned long)10 * user_datas[3];		//压带输出延时退勾针
			}
			break;
		case 6:
			if(dwTickCount >= cDelayTime3)	//压带输出延时退勾针
			{
				CLRQ01;		//勾针退
				cStepMByte2 = 7;  //拖带完成
				SETDR();   //步进电机松	
				cErrorTime2 = dwTickCount + (unsigned long)TBJ_ERRORTIME;	
			}
			break;
		case 7:
			if(X15)	//勾针退到位
			{
				cStepMByte2 = 0;
			}
			else if(dwTickCount >= cErrorTime2)
			{
				user_datas[75] = ActionPage;
				user_datas[100] = TuiGZ_W;      	//勾针退不到位警告
				M15 = 0;//cMidleCoil[0] &= ~(1<<15);  //M15	
			}
			break;	
		case 20:	//到位后反转一点
			CLRDR();
			cEncodePulse = 0;
                        MV_Set_Command_Pos_CPU(X_AXIS,0);
			user_datas[121] = 0;
			cStepMByte2 = 21;
			cDelayTime3 = dwTickCount + 50;
			if(DianJiFanZ == 0)
				cStepMByte2 = 0;	
			break;
		case 21:
			if((dwTickCount >= cDelayTime3) && !X_DRV)	
			{
				cStepMByte2 = 22;
				cWorkPulseNum = user_datas[27];
				user_datas[99] = 2;
				//if(cWorkPulseNum != 0)
				{       
                                    user_datas[99] = 1;
                                    AxisMovePosAccDec(X_AXIS, user_datas[22],cWorkPulseNum,1,5,1);
				}	
			}
			break;
		case 22:
			if(!X_DRV)	
			{
				cStepMByte2 = 0;
	//			AxisEgmStop(X_AXIS);  		//步进电机停
//				SETDR();   //步进电机松	
			}
			break;
	}
}


//送胶动作
void CSTB_SongJiao_CS(void)
{
	if(tbj_bStop)
		return;
	switch(cStepMByte1)
	{
		case 0:
			break;
		case 1: //动作开始，延时分胶
			cStepMByte1 = 2;
			cDelayTime2 = dwTickCount + (unsigned long)10 * user_datas[4];		//分胶延时输出	
			break;
		case 2:
			if((dwTickCount >= cDelayTime2) || !X11)	
			{
				cStepMByte1 = 3;
				SETQ02;				 //分胶阀
				if(CJSelect == XinYe)//鑫业的Y06为夹胶
					SETQ06;
				cDelayTime2 = dwTickCount + (unsigned long)10 * 6;		//分胶延时输出		
			}
			break;	
		case 3:							
			if(X11_UP || (user_datas[90] == 55) || ((!tbj_bRunning || (Y01 && TBJ_cOneTimes)/* || ((CJSelect == XinYe) && (SongJiaoMode == 0))*/)
			 && (dwTickCount >= cDelayTime2)))	//过链上到链上的时候送胶开始
			{
				cStepMByte1 = 4;		
			}	
			break;
		case 4:	
			//单勾针方式上升开始送胶　双勾针方式电机完成后才能送 分胶到位
			if(((SGZSelect == 1) || (cStepMByte2 == 0)) && (dwTickCount >= cDelayTime2))
			{
				if(X12 && Y02)  //分胶到位
				{
					cStepMByte1 = 5;	
					SETQ04;
					cErrorTime1 = dwTickCount + (unsigned long)TBJ_ERRORTIME;
					cDelayTime2 = dwTickCount + (unsigned long)10 * user_datas[9];
				}
			}
			break;
		case 5:
			if(X16_UP || ((SongJiaoMode == 1) && (SongJiaoDaoWei == 1) && (dwTickCount >= cDelayTime2)))
			{
				if(tbj_bRunning || M19)	//在工作状态
				{
					cStepMByte1 = 6;
					cDelayTime2 = dwTickCount + (unsigned long)15;
				}	
				else
					cStepMByte1 = 0;		
				
			}
			else if(dwTickCount >= cErrorTime1)
			{
				user_datas[75] = ActionPage;
				user_datas[100] = SongJiao_W;      	//送胶不到位警告
				M15 = 0;//cMidleCoil[0] &= ~(1<<15);  //M15	
			}
			if(X10 && tbj_bRunning)
			{
				user_datas[75] = ActionPage;
				user_datas[100] = NoJiao_W;      	//没胶警告
				M15 = 0;//cMidleCoil[0] &= ~(1<<15);  //M15	
//				tbj_bStop = 1;
				TBJ_cOneTimes = 1;	
			}
			break;
		case 6:
			if(dwTickCount >= cDelayTime2)	//普通拖带
			{
				cStepMByte1 = 7;
				CLRQ02;//关分胶
				
				if(CJSelect == XinYe)//鑫业的Y06为夹胶
				{
					CLRQ06;
				}	
				cErrorTime1 = dwTickCount + (unsigned long)TBJ_ERRORTIME;
			}
			break;	
		case 7:
			if(/*(X13 || FengJiaoSelect) && */!X12 && (dwTickCount >= cDelayTime2))	
			{
				cStepMByte1 = 8;
				if((SongJiaoMode == 0) || (!tbj_bRunning))	//气缸送胶先退，滚轮送胶先不退或是触摸屏手动退送胶
					CLRQ04;	
				cErrorTime1 = dwTickCount + (unsigned long)TBJ_ERRORTIME;		
			}
			else if(dwTickCount >= cErrorTime1)
			{
				user_datas[75] = ActionPage;
				user_datas[100] = TuiFenJiao_W;      	//退分胶不到位警告	
			}
			break;
		case 8:	
			//送胶模式　0　气缸　1 滚轮(没后接近)/感应前点离开
			if(((SongJiaoMode == 1) || (!X16 && X17)))
			{
				cStepMByte1 = 0;
				M19 = 0;
			}
			else if(dwTickCount >= cErrorTime1)
			{
				user_datas[75] = ActionPage;
				user_datas[100] = TuiJiao_W;      	//退送胶不到位警告	
			}
			break;	
	}	
}
//合模超声动作
void CSTB_HeMo_CS_CS(void)
{
	switch(cStepMByte3)	
	{
		case 0:
			break;
		case 1:
			//分胶       送胶	 	滚轮模式不退			分胶前   分胶后	                     送胶到位 退胶胶到位  滚轮方式				//单勾针方式
        	if(((!Y02) && ((!Y04) || (SongJiaoMode == 1)) && (!X12) && (X13 || FengJiaoSelect) && (((!X16) && X17) || (SongJiaoMode == 1)) && (X15 || (SGZSelect != 0))) && (dwTickCount >= cDelayTime5))
			{
				SETQ03;   // 下冲
				//下模方式　0 下模活动,1 下模不动
				if((XiaMoMode == 0) && (SGZSelect != 0))//单勾针方式
				{
					SETQ05;	
				}
				cStepMByte3 = 2;
				cErrorTime3 = dwTickCount + (unsigned long)TBJ_ERRORTIME;	
			}
			else if(!tbj_bRunning)
				cStepMByte3 = 0;	
			break;
		case 2:
		//上模下到位   单勾针方式X15才接到下模上到位 或下模不动
			if(X14 && ((X15 && (SGZSelect != 0)) || (XiaMoMode != 0)))	
			{
				cDelayTime5 = dwTickCount + (unsigned long)10 * user_datas[0];		//延时超声
				cStepMByte3 = 3;
				if(TuiGZMode == 1)	//0　先超声后下勾针，1　先下勾针后超声	
				    Y01 = 0;
			}
			break;
		case 3:
			if(dwTickCount >= cDelayTime5)
			{
				if((user_datas[90] != 55))
				{
					M09 = 0;
					Y15 = 1;		//超声开
					Y11 = 1;
					if(user_datas[6] > 150)
						cDelayTime5 = dwTickCount + (unsigned long)10 * 150;		//超声时间
					else
					{	
						if(X07 &&  (user_datas[28] < user_datas[6]))
							cDelayTime5 = dwTickCount + (unsigned long)10 * (user_datas[6] - user_datas[28]);		//超声时间	
						else
							cDelayTime5 = dwTickCount + (unsigned long)10 * user_datas[6];		//超声时间 	
					}		
					Y04 = 0;		//滚轮方式退送胶
				}
				else
				{
					cDelayTime5 = dwTickCount + (unsigned long)30;	
				}
				cStepMByte3 = 4;	
			}
			break;	
		case 4:
			if(dwTickCount >= cDelayTime5)	
			{
				cStepMByte3 = 5;
				Y15 = 0;
                                Y11 = 0;
				TBStartCuiQi();	//启动吹气
				cDelayTime5 = dwTickCount + (unsigned long)5 * user_datas[7];		//固化时间一半
			}
			break;	
		case 5:
			if(dwTickCount >= cDelayTime5)
			{
				cStepMByte3 = 6;
                                Y01 = 0;
				cDelayTime5 = dwTickCount + (unsigned long)5 * user_datas[7];		//固化时间一半		
			}
			break;
		case 6:
			if(dwTickCount >= cDelayTime5)
			{
				Y03 = 0;		//上模关
				Y05 = 0;		//下模或压带关					
				cStepMByte3 = 7;
			}
			break;	
                case 7:
			if(!X14)
			{
				cStepMByte3 = 8;
				cDelayTime5 = dwTickCount + (unsigned long)25;
			}
			break;
		case 8:		
			if(dwTickCount >= cDelayTime5)
			{	
				Y01 = 0;	//勾针下				
				cStepMByte3 = 0;
				cDelayTime5 = dwTickCount + (unsigned long)10 * 35;		
			}
			break;	
	}
}

void Hand_Action(void)
{
	unsigned char ch;
	//手动勾针,屏单独控制
	if(M0004)
	{
		M04 = 0;//cMidleCoil[0] &= ~(1<<4);  //M4	
		if(Y01)
                {
	            if(!Y03)CLRQ01;
                }
		else
		    SETQ01;	
                /*if(!X_DRV && (cStepMByte2 == 0))MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,10,1,1,2);   
                else
                    AxisEgmStop(X_AXIS);  */
                user_datas[121]++;
	}
	//手动勾针
	if(X02)
	{//             送胶前　　单勾针方式　　　　　滚轮送胶方式
		if(X02_UP && (!X16 || (SGZSelect == 1) || (SongJiaoMode == 1)))
		{
           	   Y01 = 1; 
		}
		//			双勾针选择0  双勾针(新款) 1 单勾针
		if((SGZSelect == 0))  //没触摸屏时自动压带
		{
			//勾针到位
			if(Y01 && X20 && !Y05)
			{
				Y05 = 1;
				cDelayTime2 = dwTickCount + (unsigned long)10 * user_datas[3];  //压带输出时间 
			}
			if(Y05 && (dwTickCount >= cDelayTime2))
			{
				Y01 = 0;
			}
		}
    }
 	else if(!X02 && OLDX02)
	{
		Y01 = 0;
		if((SGZSelect == 0) && (!X02 && OLDX02))//没触摸屏时自动退压带
			Y05 = 0;
	}
	//压带,在双勾针方式时有效
	if(M0003)
	{
		M0003 = 0;//cMidleCoil[0] &= ~(1<<3);  //M3	
		//双勾针方式　　　　　　下模不动
		if((SGZSelect == 0) && (XiaMoMode == 1))
		{
			if(Y05)
				Y05 = 0;
			else
				Y05 = 1;			
		}
	}
//手动前导板(分胶)
	//改动06.12.27           合模或双勾针       合模到位                 上模   下模下到位 手动超声
    if(((X03 && !OLDX03) || M0013)  && ((!Y05 && (!X15) && (SGZSelect == 1)) || ((SGZSelect == 0) && X15 && !X20)) && 
	(!Y03) && (!X14) && (!X06))
	{
		M0013 = 0;
		if(Y02 && !X03)Y02 = 0;
		else Y02 = 1;
    		
	}	
    else if(!X03 && OLDX03)Y02 = 0;
//手动送胶   当单勾针时下模信号不能有　当为双勾针时要勾针退到位（X15是复用）
	if(Y04 && (X16 && !OLDX16))
	{
		//CLRQ06;				
	}	
	//       		合模或双勾针                                         合模到位                            
    if((X05 || M0007) && ((!Y05 &&(!X15) && (SGZSelect == 1)) || ((SGZSelect == 0) && X15 && !X20))
	//上模   下模下到位 手动超声
	&& (!Y03) && (!X14) && (!X06) && (!Y04 || (X05 && !OLDX05)))
	{
		if(CJSelect == XinYe)//鑫业的Y06为夹胶
		{
			if((X05 && !OLDX05) || (!Y06 && M0007))
			{
				Y06 = 1;
				cDelayTime1 = dwTickCount + (unsigned long)70;
			}	
			else if(Y06 && (dwTickCount >= cDelayTime1))
			{
				Y04 = 1;	
				M0007 = 0;//cMidleCoil[0] &= ~(1<<7);  //M7
			}
		}
		else if(CJSelect == ChangSheng)//鑫业的Y06为夹胶
		{//手动送胶       普通拖带　　			二次拖带时勾针不能有输出
			if((X05_UP || M0007) && ((TWOTDSelect == 0) || ((TWOTDSelect == 1) && !Y01)))
			{
				Y04 = 1;	
				M0007 = 0;
			}		
		}
	 }		
         else if(!X05)
	 {
		if(CJSelect == XinYe)//鑫业的Y06为夹胶
		{
			if((!X05 && OLDX05) || M0007)
			{
				M0007 = 0;
				Y06 = 0;
				cDelayTime1 = dwTickCount + (unsigned long)120;
			}	
			else if(!Y06 && (dwTickCount >= cDelayTime1))
			{
				Y04 = 0;	
			}
			if(!Y04 && (X17 && !OLDX17))
			{
				Y06 = 1;	
			}		
		}
		else if(CJSelect == ChangSheng)//鑫业的Y06为夹胶
		{
			if((!X05 && OLDX05) || M0007)
			{
				Y04 = 0;	
				M0007 = 0;
			}		
		}			
	 }		
//手动合模
	 //手动下冲         分胶后                     分胶前    送胶到位  退胶到位   或滚轮送胶
    if((X04 || M0008) && (X13 || FengJiaoSelect) && (!X12) && (((!X16) && X17) || (SongJiaoMode == 1)) 
	//超声输出
	&& (!Y15))
	{
		if(M0008 && Y03 && !X04)
		{
			Y03 = 0;
			if(((SGZSelect == 0) && (XiaMoMode == 1)) || (XiaMoMode == 0))
			{
				Y05 = 0;
			}		
		}
		//合模输出
		else if(((X04 && !OLDX04) || M0008) && !Y03 &&((SGZSelect == 0) && X15 && !X20) || ((SGZSelect == 1) && Y01))
		{
    		    Y03 = 1;
                    if(XiaMoMode == 0)   //下模活动方式
                            Y05 = 1;
		}
		M0008 = 0;//cMidleCoil[0] &= ~(1<<8);  //M8
	}	
	else if((!X04 && OLDX04))
	{
		Y03 = 0;
		if(((SGZSelect == 0) && (XiaMoMode == 1)) || (XiaMoMode == 0))
		{
			Y05 = 0;
		}	
	}
	if((X14 && !OLDX14))	//合模到位
	{
//		if(CJSelect != XinYe)
//			TBStartCuiQi();	//启动吹气	
	}
//手动超声
	//	                                     分胶      送胶	   分胶前         分胶后                     送胶到位 退胶到位    送胶为滚轮方式             
	if((X06 || ((M09 || M10) && !X06_DW)) && (!Y02) && (!Y04) && (!X12) && (X13 || FengJiaoSelect) && (((!X16) && X17) || (SongJiaoMode == 1)) && (dwTickCount >= cDelayTime5))
	{//																		上超
		if((((SGZSelect == 0) && X15 && !X20) || (SGZSelect == 1)&& Y01) && !M12 )
		{
			if(XiaMoMode == 1) //下模不动
			{
				if(X14)//已经合模
				{
					if((X06_UP || M09) && (cStepMByte3 == 0))
					{
						cStepMByte3 = 3;  //直接发超声(按设定时间)
						M10 = 1;
					}		
				}
				else
				{
					if((X06_UP || M09) && !M10)
					{
						M10 = 1;//cMidleCoil[0] |= (1<<10);  //M10
                                                 user_datas[126]++;
						SETQ15;		//发超声
						cDelayTime5 = dwTickCount + (unsigned long)10 * user_datas[6];  //限长时间2秒	
					}
					else if(((!M09 && !X06) || (dwTickCount >= cDelayTime5)) && Y15)	
					{
						M09 = 0;//cMidleCoil[0] &= ~(1<<9);  //M9	
						M10 = 0;
						CLRQ15;
						TBStartCuiQi();
					}
				}
			}
			else if(SGZSelect == 1)//下模活动,勾针为单勾针
			{
				if((X06_UP || M09) && !M10)
				{
					M09 = 1;M10 = 1;//cMidleCoil[0] |= ((1<<10) | (1<<9)) ;  //M10
					SETQ05;		//先下模升上去
					if(X15)		//先合模的情况下直接发超声
					{
						SETQ15;		//发超声	
						cDelayTime5 = dwTickCount + (unsigned long)10 * 200;  //限长时间2秒	
					}
				}
				if(Y05 && X15_UP)
				{
					SETQ15;		//发超声
					cDelayTime5 = dwTickCount + (unsigned long)10 * 200;  //限长时间2秒		
				}
				if((!M09 || (dwTickCount >= cDelayTime5)) && Y15)	
				{
					M09 = 0;//cMidleCoil[0] &= ~(1<<9);  //M9	
					CLRQ15;
					cStepMByte3 = 4;
				}		
			}
			//手动超声完成
			if(!M09 && !Y15 && !X06)
			{
				M10 = 0;//cMidleCoil[0] &= ~(1<<10);  //M10	
				cStepMByte3 = 0;
				user_datas[128] = 0;
				if(XiaMoMode == 0) //下模活动
				{
					CLRQ05;
				}
			}	
		}
		else 
		    M09 = 0;//cMidleCoil[0] &= ~(1<<9);  //M9			
	}
	else if(X06_DW)
	{
		M10 = 0;//cMidleCoil[0] &= ~(1<<10);  //M10	
		M09 = 0;//cMidleCoil[0] &= ~(1<<9);  //M9	
		CLRQ15;	
		cStepMByte3 = 0;
		cDelayTime5 = dwTickCount + (unsigned long)10 * 30;	
		if(XiaMoMode == 0) //下模活动
		{
			CLRQ05;
		}
	}
         
//手动  上超	
	//	                           分胶       分胶前 分胶后                         送胶  送胶到位 退胶到位  手动超声
	if(M11 && !M12 && (!Y02)  && (!X12) && (X13 || FengJiaoSelect) && (((!Y04) && (!X16) && X17)   || (SongJiaoMode == 1))&& (!X06) && (dwTickCount >= cDelayTime5))
	{
		
		if(((SGZSelect == 0) && X15 && !X20) || ((SGZSelect == 1)&& Y01))
		{
			M12 = 1;//cMidleCoil[0] |= (1<<12);  //M12
			cStepMByte3 = 1;  //整个合模超声过程                      
		}
		M11 = 0;//cMidleCoil[0] &= ~(1<<11);  //M11	
	}
	else if((M12 && ((cStepMByte3 == 0) || M11)))
	{
		M11 = 0;//cMidleCoil[0] &= ~(1<<11);  //M11
		M12 = 0;//cMidleCoil[0] &= ~(1<<12);  //M12
		CLRQ03;		//上模关
		CLRQ15;		//超声关
		if((SGZSelect == 1) && (XiaMoMode == 0)) //下模活动
			CLRQ05;		//下模或压带关
		cStepMByte3 = 0; 
		cDelayTime5 = dwTickCount + (unsigned long)10 * 30;		
	}
	//自动送胶动作
	if(M0018)
	{
		M18 = 0;
		if(!Y03 && !X14 && (XiaMoMode == 1) && !Y04)
		{
			M19 = 1;
			cStepMByte1 = 1;	//分胶送开始	
		}	
	}						
}

void Auto_Run(void)
{
	switch(cStepMByte)
	{
		case 0:
			break;
		case 1:
			cStepMByte = 2;
			CLRDR();
			
			cDelayTime1 = dwTickCount + (unsigned long)200;  //先锁轴
			cTest1 = 0;
			cSetEncode = 0;
			break;	
		case 2:  //第一条时
			if(dwTickCount >= cDelayTime1)
			{
				cStepMByte = 3;	
				cStepMByte1 = 1;	//分胶送开始
				 MV_Set_Command_Pos_CPU(X_AXIS,0);
				if(!Y01)
					cStepMByte2 = 1;	//拖带电机开始	
			}
			break;
		case 3:
		//		送胶完成
			if((cStepMByte1 == 0) && (cStepMByte2 == 0))
			{
				cStepMByte = 4;	
				if(cTest1 == 1)
					cSetEncode = cEncodePulse;
				if(DianJiFanZ == 1)
					cStepMByte2 = 20;	//拖带电机反转一点	
				else
					SETDR();	
				cDelayTime1 = dwTickCount + (unsigned long)1000;  // 退分胶到位要警告	
			}
			break;	
		case 4:
			 //分胶      分胶前     分胶后                       送胶 送胶到位 退胶到位		滚轮方式　            双勾针方式时勾针要退到位　　　　　　　单勾针方式
			if((!Y02) && (!X12) && (X13 || FengJiaoSelect) && (((!Y04) &&(!X16) && X17)  || (SongJiaoMode == 1))&& (((SGZSelect == 0) && X15 && !X20) || (SGZSelect == 1)))
			{
				if(cStepMByte2 == 0)
				{
					cStepMByte = 5;	
					cStepMByte3 = 1;
				}	
			}
			break;	
		case 5:
			if(cStepMByte3 == 0)
			{
				cStepMByte = 6;		
				
				CLRQ01;	
				if(TBJ_cOneTimes == 1)
				{
					SETDR();
					tbj_bStop = 1;	
				}
				else
				{
					CLRDR();	
					CalProSP(78);		//计算生产速度

				}
				AddToTal(76);	//产量加1保存
			}
			break;
		case 6:
			if(!X14 && (((SGZSelect == 0) && X15 && !X20) || ((XiaMoMode == 0) && !X15) || ((XiaMoMode == 1) && (SGZSelect == 1))))	//上模离开
			{
				cStepMByte = 7;	
				cDelayTime1 = dwTickCount + (unsigned long)30;  //先锁轴	
			}
			break;
		case 7:
			if(dwTickCount >= cDelayTime1)
			{				
				cStepMByte = 2;	
				cTest1++;
				if(cTest1 > 2)
					cTest1 = 3;	
			}
			break;							
	}				
}
#endif