GC23005/Machine/TongYongMachine/TYMXC_NiLong_StepJi.c

#include "global.h"

#if TONG_YONG_MACHINE

void MXC_NiLongCheckStart(void);
void MXC_NiLongMotor(void);
void MXC_NiLongXiaChong(void);
void MXC_NiLongFenZhen(void);
void MXC_NiLongChuiQi(void);
void MXC_ManualAction(void);
void MXC_AutoAction(void);
unsigned char MXC_CheckPos(void);

unsigned char cLFengTimer,cRFengTimer;
unsigned long cShaCheTime,cLaLianLine,cGouZhenTime;
unsigned char cChuiQiStep = 0,cGouZhenResetOK;
unsigned short cBudaiCheckDelay = 0;
unsigned char bHandWork,bPulseTatol_EN,bFirst,cInt1_OK,cStopFlag,cOneTimes;
long cSetEncode,cTotal,cDinWeiTime,cAddSetPulseNum,cEncodePulse,cWorkPulseNum;
unsigned long cZipperLength[2];
unsigned char cCheckLengthOk=0,cDaoJu_Flag=0;
unsigned char STOP_IN_FLAG,STOP_IN_FLAG_OLD,STOP_FILTER;
unsigned char MXC_SingOneFlag = 0;
unsigned char MXC_KD_Flag = 0,KD_GO_ON_FLAG = 0,cAlarmStopFlg = 0;
long MXC_KD_pos = 0,save_pos_buff = 0;
long MXC_dwEncPos = 0;
unsigned long MXC_SaveLength = 0;

//故障报警
void MXC_SetAlarmCode(unsigned alarm_code)
{
    SetAlarmCode(MXC_ALARM_ADDR,alarm_code);
    MXC_bAlarmStop = 1;
    cAlarmStopFlg  = 1;
}

//高速输入X20外部色标信号中断
void MXC_ExtiActionX20(void)
{
     if(cSeBiaoEn && !cSeBiaoOk)
    {
        cSeBiaoOk = 1;
        cSeBiaoEn  = 0;
        if(X_DRV)SetRemainLength(X_AXIS, MXC_PARAM_SEBIAO_DW_LENGTH,MXC_PARAM_SB_OFFSET_SPEED);
    }
}

//高速输入X31/X17外部信号中断
void MXC_ExtiActionX31(void)
{

}
void MXC_InitAction(void)
{
    float length_buff,pulse_buff;
    
    CalFreqTab_X_Free(25);
    length_buff = MXC_PARAM_DAILUN_LENGTH;
    pulse_buff  = MXC_PARAM_CYCLE_PULSE;
    XGearRatio  = pulse_buff/length_buff;
    
    length_buff = MXC_BM_LENGTH;
    pulse_buff  = 1000;
    BMGearRatio  = pulse_buff/length_buff;
    
    MXC_SZ_OUT = MXC_SERVER_DISEN;				 
    
    STOP_IN_FLAG = STOP_IN;
    STOP_IN_FLAG_OLD = STOP_IN_FLAG;
    MXC_SaveLength = 0;
}

void MXC_NiLongXiuCiJiAction(void)
{
    MXC_NiLongCheckStart();  //启动
    MXC_NiLongFenZhen();     //左右分针
    MXC_NiLongXiaChong();   //下冲
    MXC_NiLongChuiQi();
    MXC_NiLongMotor();			//拖带控制
    MXC_ManualAction();
    MXC_AutoAction();	
}

void MXC_ManualAction(void)
{
      long i;
      short *len_buff;
      //清总产量
      if(MXC_bClear)         //清总产量
      {
          MXC_bClear = 0;
          ClrcToTal(MXC_TOTAL_ADDR);
          MXC_bSaveWorkData = 1;
      }

      //当长度改变时，生产总量自动清零
      if(MXC_bChangeLength)
      {
          MXC_bChangeLength = 0;
          MXC_SaveLength = 0;
          MXC_bClear = 1;
      }
      //加10
      if(MXC_bAddLength)
      {
          MXC_bAddLength = 0;
          i = MXC_SET_REVISE_ZIPPER_LENGTH;
          i += 10;
          SetData32bits(MXC_ZIPPER_LENGTH_ADDR,i);
      }
      //减10
      if(MXC_bDecLength)
      {
          MXC_bDecLength = 0;
          i = MXC_SET_REVISE_ZIPPER_LENGTH;
          i -= 10;
          SetData32bits(MXC_ZIPPER_LENGTH_ADDR,i);		
      }
      //工作方式选择(数控定寸和勾针定寸)　
      if(MXC_bSetDCMode)
      {
          MXC_bSetDCMode = 0;
          MXC_SaveLength = 0;
          
          MXC_DC_MODE++;
          
          if(MXC_DC_MODE > MXC_DC_BMQ_MODE)MXC_DC_MODE = MXC_DC_GZ_MODE;
          
          if(MXC_DC_MODE != 0)	
          {
              MXC_GouZhen_VAVLE = 1;	
              MXC_cGouZhenTime  = 300;
              MXC_XiaZhi_MOTOR = 0;  
          }
          
          if(MXC_DC_MODE == MXC_DC_SF_MODE)
          {
              MV_Set_Command_Pos_CPU(X_AXIS,0);
          }
      }

      if(MXC_bSetLength)
      {
          MXC_bSetLength = 0;
          if(MXC_PARAM_INCH_MODE)
          {
              SetData32bits(15,CalLengthCM(MXC_SET_ZIPPER_LENGTH_INCH));
              len_buff = &MXC_SET_REVISE_ZIPPER_LENGTH_INCH;
              MXC_SET_REVISE_ZIPPER_LENGTH = CalLengthCM2(*len_buff);
          }
          else
          {
              SetData32bits(18,CalInch(MXC_SET_ZIPPER_LENGTH));
              len_buff = &MXC_SET_REVISE_ZIPPER_LENGTH;
              MXC_SET_REVISE_ZIPPER_LENGTH_INCH = CalInch2(*len_buff);
          }
          MXC_SaveLength = 0;
      }
    
      if((MXC_bRunning) == 0) ////手动 
      {        
          if(MXC_bXiaChong)   
          {
              MXC_bXiaChong = 0;
              MXC_SaveLength = 0;
              if(MXC_cXiaChongStep == 0)MXC_cXiaChongStep = 1;
          }
          
          if(MXC_bLeftFenZhen)
          {
              MXC_bLeftFenZhen      = 0;
              
              if(MXC_cXiaChongStep == 0) MXC_LeftFenZhen_VAVLE = ~MXC_LeftFenZhen_VAVLE;
             
          }
        
          if(MXC_bRightFenZhen)
          {
              MXC_bRightFenZhen     = 0;
              if(MXC_cXiaChongStep == 0)MXC_RightFenZhen_VAVLE= ~MXC_RightFenZhen_VAVLE;
          }
              
          //点动下冲
          if((MXC_bDotXiaChong))
          {
              MXC_bDotXiaChong = 0;
              if(MXC_LeftFenZhen_IN && MXC_RighttFenZhen_IN)
              {
                  if(MXC_cXiaChongStep == 0)MXC_cXiaChongStep = 20;
              }
              else
              {
                   MXC_SetAlarmCode(MXC_XIA_CHONG_ALARM);		//下冲条件不满足
              }
          }
              
          if(MXC_bGouZhen)
          {
              MXC_bGouZhen = 0;
              MXC_cGouZhenTime  = dwTickCount + 300;
              MXC_GouZhen_VAVLE = 1;			
          }
            
          if(MXC_DC_MODE != MXC_DC_GZ_MODE)   //伺服定寸
          {      
              MXC_GouZhen_VAVLE = 1;
          }
          else
          {
              if(dwTickCount >= MXC_cGouZhenTime) MXC_GouZhen_VAVLE = 0;
          }
          
          if(MXC_bChuiQi)
          {
              MXC_bChuiQi = 0;
              if(MXC_cChuiQiStep == 0)MXC_cChuiQiStep = 1;
          }
          
        if(MXC_bTestMotor)
        {
            if(!X_DRV && MXC_CheckPos())MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P, 10,1,5,5);   
        }
        else 
        {
            if(X_DRV)AxisDecStop(X_AXIS);  
        }
            
      }
      
      
}

void MXC_AutoAction(void)
{
    DISPLAY_DATA0 = MXC_cAutoStep;
    DISPLAY_DATA1 = MXC_cMotorStep;
    DISPLAY_DATA2 = MXC_SaveLength;
    DISPLAY_DATA3 = MXC_cRightFenZhenStep;
    DISPLAY_DATA4 = MXC_cXiaChongStep;
    DISPLAY_DATA5 = dwRealPos;
    DISPLAY_DATA6 = MXC_dwEncPos;
    
    if(MXC_XZ_ENABLE)MXC_XiaZhi_MOTOR = 1;
    else MXC_XiaZhi_MOTOR = 0;
    
    if(dwTickCount >= MXC_cXiaZhiDelay)MXC_XiaZhi_VAVLE = 0;
    
    if(MXC_bRunning)
    {   
        switch(MXC_cAutoStep)
        {
            case 0:
                    break;
            case 1:
                    if(dwTickCount >= MXC_cAutoDelay)
                    {

                         MXC_cAutoStep = 2;
                    }
                    break;
            case 2:
                    //左右分针要退到位，过链到位要离开
                    if(dwTickCount >= MXC_cAutoDelay)
                    {
                        MXC_cAutoStep = 3;
                        switch(MXC_DC_MODE)
                        {
                            case MXC_DC_SF_MODE:MXC_cMotorStep = 20; break;        //伺服
                            case MXC_DC_SB_MODE:MXC_cMotorStep = 40; break;        //色标
                            case MXC_DC_BMQ_MODE:MXC_cMotorStep = 60; break;        //编码器
                            default:MXC_cMotorStep = 1;   //启动拖带 ;//勾针
                        }
                        
                    }     			
                    break;
            case 3:
                    //拖带已经完成
                    if(MXC_cMotorStep == 0)
                    {
                         if(SingOneFlg)
                        {
                            dwZipCnt   = 0;
                            SingOneFlg = 0;
                            MXC_cAutoStep = 0;
                            MXC_bRunning = 0;
                        }
                        else
                        {
                            MXC_cAutoStep = 4;
                        }
                    }
                    break;	
            case 4:
                        MXC_cAutoStep = 5;
                    break;
            case 5:
                    //左右分针都已完成
                    if((MXC_cLeftFenZhenStep == 0) && (MXC_cRightFenZhenStep == 0))
                    {
                        MXC_cXiaChongStep = 1;   //下冲电机启动
                        MXC_cAutoStep = 6;	
                    }
                    break;
            case 6:  //下冲已完成
                    if((MXC_cXiaChongStep == 0) || (MXC_cXiaChongStep == 5))
                    {
                        switch(MXC_DC_MODE)
                        {
                            case MXC_DC_SF_MODE:
                            {
                                MXC_SaveLength += MXC_PARAM_DAOKOU_LENGTH;         
                                if(MXC_SaveLength >= MXC_PARAM_KONG_WEI_LENGTH)
                                {
                                    dwZipCnt++;
                                    MV_Set_Command_Pos_CPU(X_AXIS,0);
                                    MXC_SaveLength = 0;
                                    AddToTal(MXC_TOTAL_ADDR);	 //计数增加和保存
                                    CalProSP(MXC_PROSPEED_ADDR);
                                    MXC_cAutoStep = 7;                           
                                }   
                                else
                                {
                                    if((MXC_PARAM_KONG_WEI_LENGTH - MXC_SaveLength) >= MXC_PARAM_DAOKOU_LENGTH)
                                    {
                                        MXC_cAutoStep = 2; 
                                    }
                                    else
                                    {
                                        MXC_SaveLength = MXC_PARAM_KONG_WEI_LENGTH - MXC_PARAM_DAOKOU_LENGTH;
                                        MXC_cAutoStep = 2; 
                                    }
                                }                                
                            }break;        //伺服
                            case MXC_DC_BMQ_MODE:
                            {
                                MXC_SaveLength += MXC_PARAM_DAOKOU_LENGTH;         
                                if(MXC_SaveLength >= MXC_PARAM_KONG_WEI_LENGTH)
                                {
                                    dwZipCnt++;
                                    SetEncodePos(0);
                                    MXC_SaveLength = 0;
                                    AddToTal(MXC_TOTAL_ADDR);	 //计数增加和保存
                                    CalProSP(MXC_PROSPEED_ADDR);
                                    MXC_cAutoStep = 7;                           
                                }   
                                else
                                {
                                    if((MXC_PARAM_KONG_WEI_LENGTH - MXC_SaveLength) >= MXC_PARAM_DAOKOU_LENGTH)
                                    {
                                        MXC_cAutoStep = 2; 
                                    }
                                    else
                                    {
                                        MXC_SaveLength = MXC_PARAM_KONG_WEI_LENGTH - MXC_PARAM_DAOKOU_LENGTH;
                                        MXC_cAutoStep = 2; 
                                    }
                                }                               
                            }
                            break;        //编码器
                            default:
                            {
                                dwZipCnt++;
                                AddToTal(MXC_TOTAL_ADDR);	 //计数增加和保存
                                CalProSP(MXC_PROSPEED_ADDR);
                                MXC_cAutoStep = 7;   
                            }
                        }                     
                    }
                    break;		
            case 7:
                    if(MXC_LeftFenZhen_Origin_IN && MXC_RightFenZhen_Origin_IN && !MXC_LeftFenZhen_IN && !MXC_RighttFenZhen_IN && !MXC_GouZhen_IN)
                    {
                        if(GetTotal(MXC_TOTAL_ADDR) >= MXC_SET_TOTAL)MXC_SetAlarmCode(MXC_TOTAL_ALARM);
                        
                        MXC_cAutoStep = 8;
                    }
                    break;	
            case 8:
                        MXC_cAutoDelay = dwTickCount + MXC_PARAM_MOTOR_DELAY;
                        
                        if(MXC_SingOneFlag)
                        {
                            dwZipCnt   = 0;
                            MXC_SingOneFlag = 0;
                            MXC_cAutoStep = 0;
                            MXC_bRunning = 0;
                        }
                        MXC_cAutoStep = 1;	
                    break;		                     
        }		         
    }
}

// 检测是否踏了脚踏开关
void MXC_NiLongCheckStart(void)
{
    //  停止键        不能在工作,手动,停止过程中                                
    if((MXC_bRunning == 0) && (START_IN_UP || MXC_bStart || MXC_bNext))
    {
        if(!MXC_LeftFenZhen_Origin_IN)MXC_SetAlarmCode(MXC_LFZ_ORIGIN_ALARM);	//没拉链
        else if(GetTotal(MXC_TOTAL_ADDR) >= MXC_SET_TOTAL)MXC_SetAlarmCode(MXC_TOTAL_ALARM);
        else if(!MXC_RightFenZhen_Origin_IN)MXC_SetAlarmCode(MXC_RFZ_ORIGIN_ALARM);
        else if((MXC_PARAM_SEBIAO_DW_LENGTH > MXC_SET_ZIPPER_LENGTH) && (MXC_DC_MODE==2))MXC_SetAlarmCode(MXC_SEBIAO_ZIPPER_LENGTH_ALARM);
        else if(MXC_KaDai_IN)MXC_SetAlarmCode(MXC_KA_DAI_ALARM);
        else
    	{
            if(MXC_bNext)
            {
               SingOneFlg = 1;   
               MXC_bNext  = 0;
            }
            MXC_bRunning = 1;
            MXC_cAutoStep = 1;	              
            cGouZhenTime = 1;   
            cCheckLengthOk = 0;
            cZipperLength[0] = 0;			
            cZipperLength[1] = 0;
            dwZipCnt = 0;
            MXC_cAutoDelay = dwTickCount;
            MXC_cMotorDelay = dwTickCount;
            MXC_cXiaChongDelay = dwTickCount;
            
    	}
    	MXC_bStart = 0;
    }

	//卡带感应
    if(MXC_KaDai_IN && (dwTickCount >= MXC_cKaDaiDelay))
    {
        MXC_SetAlarmCode(MXC_KA_DAI_ALARM);      
	MXC_cKaDaiDelay = dwTickCount + 2200;
    }
    
    
    if(MXC_KaDai_IN_UP)
    {
        if(MXC_cChuiQiStep == 0)MXC_cChuiQiStep = 1;
    }		
 //停止
   STOP_IN_FLAG_OLD = STOP_IN_FLAG;
    
   if(STOP_IN)
   {
       if(STOP_FILTER < 50)
       {
           STOP_FILTER++;
       }
       else
           STOP_IN_FLAG = 1;
   }
   else if(STOP_FILTER > 25)
   {
       STOP_FILTER--;
   }
   else
       STOP_IN_FLAG = 0;
   
    if(MXC_bStop)
    {
        MXC_bStop = 0;
        if(MXC_bRunning)MXC_SingOneFlag = 1;
    }
    
    
   
    if(((STOP_IN_FLAG && !STOP_IN_FLAG_OLD)))
    { 
        MXC_bStop = 0;
        if(MXC_bRunning)
        {
           if(MXC_cXiaChongStep==0)
           {
              if(MXC_cChuiQiStep == 0)MXC_cChuiQiStep = 1;
              
             // if(!MXC_XiaChong_MOTOR)MXC_XC_SongZhou = MXC_SERVER_DISEN;           
           }
           
            MXC_bRunning = 0;  
            MXC_cAutoStep = 0;
            MXC_cMotorStep = 0;
            AxisDecStop(X_AXIS);
            MXC_cJiaoDaoStep = 0;
            SingOneFlg    = 0;
            MXC_SingOneFlag = 0;
        }
        else
        {
            MXC_bRunning = 0;
                    
            cStopFlag = 0;
            MXC_cAutoStep = 0;
            MXC_cMotorStep = 0;
            MXC_cXiaChongStep = 0;
            MXC_cLeftFenZhenStep = 0;
            MXC_cRightFenZhenStep = 0;
            MXC_cJiaoDaoStep = 0;
            MXC_cDCPStep  = 0;
            MXC_XiaZhi_VAVLE     = 0;
            MXC_LeftFenZhen_VAVLE = 0;
            MXC_RightFenZhen_VAVLE = 0; 
            SingOneFlg    = 0;
            MXC_SingOneFlag = 0;
/*            if(MXC_XiaChongMotorMode)
                MXC_XC_SongZhou = MXC_SERVER_DISEN;  
            else
                MXC_XC_ShaChe   = MXC_SC_DISEN;*/
           MXC_XC_ShaChe = MXC_SC_DISEN; 
           if((MXC_cChuiQiStep == 0) &&(MXC_cXiaChongStep==0))MXC_cChuiQiStep = 1;      
           AxisDecStop(X_AXIS);
           SetAlarmCode(MXC_ALARM_ADDR,MXC_NO_ALARM);
        }
    }
    
 /*   if(!MXC_bRunning && (MXC_cMotorStep==0) && (MXC_cXiaChongStep == 0))
    { 
      if(!X_DRV)MXC_TuoDaiSongZhou = MXC_SERVER_DISEN;	 
    }*/
    if(MXC_bAlarmStop)
    {
        MXC_bAlarmStop = 0;
        MXC_bRunning = 0;
        MXC_cAutoStep = 0;
        MXC_cMotorStep = 0;
        MXC_cLeftFenZhenStep = 0;
        MXC_cRightFenZhenStep = 0; 
        MXC_cDCPStep          = 0;
        MXC_LeftFenZhen_VAVLE = 0;
        MXC_RightFenZhen_VAVLE = 0;
        MXC_SingOneFlag        = 0;
        AxisDecStop(X_AXIS); 
        
        if((GetAlarmCode(MXC_ALARM_ADDR) == MXC_XIA_CHONG_ALARM) || (GetAlarmCode(MXC_ALARM_ADDR) == MXC_XC_ALARM) ||
            (GetAlarmCode(MXC_ALARM_ADDR) == MXC_LFZ_ORIGIN_ALARM) || (GetAlarmCode(MXC_ALARM_ADDR) == MXC_LFZ_LIMIT_ALARM) ||
             (GetAlarmCode(MXC_ALARM_ADDR) == MXC_RFZ_ORIGIN_ALARM) || (GetAlarmCode(MXC_ALARM_ADDR) == MXC_RFZ_LIMIT_ALARM)) 
        {
            MXC_cXiaChongStep = 0;
            MXC_XiaChong_MOTOR = 0;
        }
    }
}   


void MXC_NiLongChuiQi(void)
{	
      //吹气
    if(MXC_XiaChong_IN_UP)
    {
        if(MXC_cChuiQiStep == 0)MXC_cChuiQiStep = 1;
    }
    
      
    switch(MXC_cChuiQiStep)
    {
        case 1:
            MXC_cChuiQiStep = 2;
            if(MXC_bRunning)MXC_cChuiQiDelay = dwTickCount+MXC_PARAM_DELAY_CHUIQI_TIME;            
        break;
        case 2:
            if(dwTickCount >= MXC_cChuiQiDelay)
            {
                MXC_cChuiQiDelay = dwTickCount + MXC_PARAM_CHUIQI_TIME;	
                MXC_ChuiQi_VAVLE = 1;//
                MXC_cDCPStep = 1;
                MXC_cChuiQiStep = 3;                
            }
        break;
        case 3:
            if(dwTickCount >= MXC_cChuiQiDelay)
            {
                MXC_ChuiQi_VAVLE = 0;//
                MXC_cChuiQiStep = 0;
            }
        break;
    }
}

unsigned char ComPareLength(void)
{
    if((cZipperLength[0] != 0) && (cZipperLength[1] != 0))
    {
		if(cZipperLength[0] > cZipperLength[1])
		{
		    if((cZipperLength[0] - cZipperLength[1]) > 200)
			{
			    return 0;
			}
			else 
			    return 1;
		}
		else
	    {
		    if((cZipperLength[1] - cZipperLength[0]) > 200)
			{
			    return 0;	
			}
			else
			    return 1;
		}
	}
	else 
	    return 0;
}

unsigned char MXC_CheckPos(void)
{
      unsigned long zipper_length;
      short *revise_buff;
      if(MXC_DC_MODE == MXC_DC_BMQ_MODE)
      {
          revise_buff = &user_datas[17];
          zipper_length =  MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH;
          if(MXC_dwEncPos >= zipper_length)return 0;
          else
             return 1;
      }
      else if(MXC_DC_MODE == MXC_DC_GZ_MODE)
      {
          if(MXC_GouZhen_IN)
              return 0;
          else
              return 1;
      }
      else if(MXC_DC_MODE == MXC_DC_GZ_MODE)
      {
          revise_buff = &user_datas[17];
          zipper_length =  MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH;
          if((0 - dwRealPos) > zipper_length) return 0;
          else
            return 1;
      }
      else
        return 1;
}

void  MXC_NiLongMotor(void)
{
        static long save_buff,gou_zhen_buff,zipper_length_buff;
	static unsigned long zipper_length;
        short *revise_buff;
        
        dwRealPos = GetPos(X_AXIS);
        MXC_dwEncPos  = GetEncodePos();
        
        if(MXC_bRunning)
        {
            if(!MXC_Zipper_IN && (MXC_DC_MODE != MXC_DC_BMQ_MODE)) MXC_SetAlarmCode(MXC_NO_ZIPPER_ALARM);        
        }
        
        if(!MXC_bRunning)
        {
            if(MXC_CheckPos() == 0)AxisEgmStop(X_AXIS);  
        }

	switch(MXC_cMotorStep)
	{
		case 0:
                break;
                case 1:
                    if(MXC_SZ_OUT == MXC_SERVER_DISEN)
                    {
                        MXC_SZ_OUT = MXC_SERVER_EN;
                        MXC_cMotorDelay = dwTickCount + 50;   //先锁轴              
                    }
                    MXC_cMotorStep = 2;
                break;
		case 2://勾针模式
                if(dwTickCount >= MXC_cMotorDelay)                 
                {
                     save_buff  = dwRealPos;       
                     revise_buff = &user_datas[17];
                     save_pos_buff = dwRealPos;
                     if(cCheckLengthOk)
                     {
                         MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_SET_SPEED,1,5,1);                            
                     }
                     else
                     {
                          if(cCheckLengthOk == 0)
                          {
                              cZipperLength[0] = cZipperLength[1];			
                              cZipperLength[1] = zipper_length_buff - dwRealPos;
                              zipper_length_buff = dwRealPos;
                              if(ComPareLength())
                              {
                                  cCheckLengthOk = 1;
                              }
                          }

                         if(cCheckLengthOk)zipper_length =  cZipperLength[1] + (*revise_buff);
                         MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_FIRST_SPEED,1,5,1);                                
                     }
                     MXC_cMotorDelay = dwTickCount + MXC_PARAM_MOTOR_ALARM_TIME;  
                     MXC_cGouZhenTime = dwTickCount + MXC_PARAM_GZ_DELAY;
                     MXC_cMotorStep = 3;
                }	
                break;	
		case 3:
                        if(((dwTickCount >= MXC_cGouZhenTime)&&(MXC_PARAM_GZ_RESET_MODE==0)) || (cCheckLengthOk == 0))MXC_GouZhen_VAVLE = 0;

                            if(MXC_PARAM_AUTO_CHECK_MODE)
                            {
                                if(cCheckLengthOk)
                                {
                                    if(((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_GZ_LENGTH))&&MXC_PARAM_GZ_RESET_MODE)MXC_GouZhen_VAVLE = 0;
                                    
                                    if((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_LOWSPEED_LENGTH))
                                    {    
                                        AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                                        MXC_cMotorStep = 4; 
                                    }    
                                }
                                else
                                {
                                     if(MXC_GouZhen_IN)
                                    {
                                        MXC_GouZhen_VAVLE = 0;
                                        MXC_cMotorStep = 5;
                                        AxisEgmStop(X_AXIS);     
                                    }  
                                    else
                                    {
                                        if(dwTickCount >= MXC_cGouZhenTime)MXC_GouZhen_VAVLE = 0;
                                         MXC_cMotorStep = 4; 
                                    }                                    	
                                }
                                
                            }
     
                        if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;	
		case 4:    
                        if(((dwTickCount >= MXC_cGouZhenTime)&&(MXC_PARAM_GZ_RESET_MODE==0)) || (cCheckLengthOk == 0))MXC_GouZhen_VAVLE = 0;

                        if(MXC_PARAM_AUTO_CHECK_MODE)
                        {
                            if(((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_GZ_LENGTH))&&MXC_PARAM_GZ_RESET_MODE &&cCheckLengthOk)MXC_GouZhen_VAVLE = 0;
                        }
                        else
                        {
                            if(((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_GZ_LENGTH))&&MXC_PARAM_GZ_RESET_MODE)MXC_GouZhen_VAVLE = 0;
                        }
                        
                        if(MXC_GouZhen_IN)
                        {
                            MXC_GouZhen_VAVLE = 0;
                            MXC_cMotorStep = 5;
                            AxisEgmStop(X_AXIS);     
                        }   
                        
                        if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;
		case 5:	
                        if(((dwTickCount >= MXC_cGouZhenTime)&&(MXC_PARAM_GZ_RESET_MODE==0)) || (cCheckLengthOk == 0))MXC_GouZhen_VAVLE = 0;
                        if(!X_DRV)
                        {
                            MXC_cMotorStep = 0;     
                            MXC_cMotorDelay = dwTickCount;
                        }
                        else if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;		
                case 20:
                        if(MXC_SZ_OUT == MXC_SERVER_DISEN)
                        {
                            MXC_SZ_OUT = MXC_SERVER_EN;
                            MXC_cMotorDelay = dwTickCount + 50;   //先锁轴   
                        }
                        MXC_cMotorStep = 21;
                        break;
                case 21: 
                        if(dwTickCount >= MXC_cMotorDelay)   //电机定寸模式
                        {
                            revise_buff = &user_datas[17];
                                                       
                            if(cAlarmStopFlg)
                            {
                                zipper_length = MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH;
                                cAlarmStopFlg = 0;
                            }
                            else
                            {  
                                zipper_length = MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH + MXC_SaveLength;
                                if((0 - dwRealPos) > zipper_length)
                                    zipper_length = 0;//MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH;
                                else
                                    zipper_length = MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH + MXC_SaveLength - (0 - dwRealPos);
                            }

                            AxisMovePosAccDec(X_AXIS,MXC_PARAM_SET_SPEED,zipper_length,1,5,1);
                            MXC_GouZhen_VAVLE = 1;			 //定位(活动勾针)电磁阀
                            MXC_cMotorStep = 22;
                            MXC_cMotorDelay = dwTickCount + MXC_PARAM_MOTOR_ALARM_TIME;   
                        }
                break;
 		case 22:
                        if(!X_DRV)
                        {
                            MXC_cMotorStep = 0;
                            MXC_cMotorDelay = dwTickCount;
                        }
                        else if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);                
                        break;
                case 40:
                    if(MXC_SZ_OUT == MXC_SERVER_DISEN)
                    {
                        MXC_SZ_OUT = MXC_SERVER_EN;
                        MXC_cMotorDelay = dwTickCount + 50;   //先锁轴              
                    }
                    MXC_cMotorStep = 41;
                break;       
                case 41:
                     if(dwTickCount >= MXC_cMotorDelay)   
                     {
                         save_buff  = dwRealPos; 
                          revise_buff = &user_datas[17];
                         zipper_length = MXC_SET_ZIPPER_LENGTH + (*revise_buff);
                         
                         if((dwZipCnt==0)||SingOneFlg)MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_SB_LOW_SPEED,1,5,1);   
                         else MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_SB_HIGH_SPEED,1,5,1);   
                         
                         cSeBiaoOk = 0;
                         cSeBiaoEn = 0;  
                         MXC_cMotorStep = 42;                           
                         MXC_GouZhen_VAVLE = 1;			 //定位(活动勾针)电磁阀
                         MXC_cMotorDelay = dwTickCount +  MXC_MOTOR_ALALRM_TIME;
                     }
                  break;
		case 42:
                        if(dwZipCnt==0)
                        {
                            cSeBiaoOk = 0;
                            cSeBiaoEn = 1;  
                            MXC_cMotorStep   = 43;
                        }
                        else
                        {
                            if((save_buff - dwRealPos + MXC_PARAM_LOWSPEED_LENGTH) >= (zipper_length  -MXC_PARAM_SEBIAO_DW_LENGTH)) AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                            if((save_buff - dwRealPos + MXC_PARAM_SEBIAO_TQ_LENGTH) >= (zipper_length - MXC_PARAM_SEBIAO_DW_LENGTH))
                            {
                                cSeBiaoOk = 0;
                                cSeBiaoEn = 1; 
                                MXC_cMotorStep   = 43;
                            }
                            else if((save_buff - dwRealPos) > (zipper_length + MXC_ERROR_LENGTH))MXC_SetAlarmCode(MXC_NO_SEBIAO_ALARM);
                            
                        }                        
                        break;	
		case 43:
                        if(dwZipCnt!=0)
                        {
                            if((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_LOWSPEED_LENGTH)) AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                            if((save_buff - dwRealPos) > (zipper_length + MXC_ERROR_LENGTH))MXC_SetAlarmCode(MXC_NO_SEBIAO_ALARM);
                        }
                        
                        if(!X_DRV)
                        {
                            if(dwZipCnt!=0)
                            {
                                if((save_buff - dwRealPos) < (zipper_length - MXC_ERROR_LENGTH))MXC_SetAlarmCode(MXC_NO_SEBIAO_ALARM);
                            }
                            MXC_cMotorStep = 0;
                            MXC_cMotorDelay = dwTickCount;
                        }
                        else if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_NO_SEBIAO_ALARM);
                        break;	
                case 60:
                    if(MXC_SZ_OUT == MXC_SERVER_DISEN)
                    {
                        MXC_SZ_OUT = MXC_SERVER_EN;
                        MXC_cMotorDelay = dwTickCount + 50;   //先锁轴  
                    }
                    MXC_cMotorStep = 61;
                break;
		case 61:
                if(dwTickCount >= MXC_cMotorDelay)                 
                {
                     save_buff  = MXC_dwEncPos;       
                     revise_buff = &user_datas[17];
                     zipper_length =  MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH + MXC_SaveLength;
                     MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_SET_SPEED,1,5,1);                              
                     MXC_cMotorDelay = dwTickCount + MXC_PARAM_MOTOR_ALARM_TIME;   
                     MXC_cMotorStep = 62;
                }	
                break;	
		case 62:                                   
                        if((MXC_dwEncPos) >= (zipper_length - MXC_PARAM_LOWSPEED_LENGTH))
                        {    
                            AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                            MXC_cMotorStep = 63; 
                        }                            
                        else if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;	
		case 63:    
                        if((MXC_dwEncPos) >= zipper_length)
                        {
                            MXC_cMotorStep = 64;
                            AxisEgmStop(X_AXIS);     
                        }   
                        else if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;
		case 64:	
                        if(!X_DRV)
                        {
                            MXC_cMotorStep = 0;    
                            MXC_cMotorDelay = dwTickCount;
                        }
                        else if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;		
	}
}
//下冲
void  MXC_NiLongXiaChong(void)
{       
    switch(MXC_cXiaChongStep)
    { 
    case 0:
            return;
            break;
    case 1:
            {
                MXC_cRightFenZhenStep = 1;	
                MXC_cLeftFenZhenStep  = 0;
                cRFengTimer = 0;
                cLFengTimer = 0;
            }
            MXC_cXiaChongStep = 2;
            break;
    case 2:
            if((MXC_cRightFenZhenStep==0) && (MXC_cLeftFenZhenStep==0))
            {
                  MXC_XC_ShaChe   = MXC_SC_DISEN;

                  if(MXC_bRunning)MXC_cXiaChongDelay = dwTickCount + MXC_PARAM_DELAY_XC;
                  MXC_cXiaChongStep = 3;
            }
            break;
    case 3:
            if(dwTickCount >= MXC_cXiaChongDelay)
            {
                    MXC_cXiaChongStep = 4;	
                    MXC_XiaChong_MOTOR = 1;  //下冲电机  
                    if(!MXC_bRunning)MV_Set_Command_Pos_CPU(X_AXIS,0);
                    if(!MXC_bRunning)SetEncodePos(0);
                    MXC_cXiaChongDelay = dwTickCount + (unsigned long)MXC_ERRORTIME;   //下冲最长时间   	
                    
                    if(MXC_bRunning && MXC_XZ_ENABLE)   
                    {
                        if(MXC_DC_MODE == MXC_DC_GZ_MODE)
                        {
                            MXC_XiaZhi_VAVLE = 1;
                            MXC_cXiaZhiDelay = dwTickCount + MXC_PARAM_XIAZHI_TIME;
                        }
                        else
                        {
                            if(MXC_PARAM_DAOKOU_LENGTH >= MXC_PARAM_KONG_WEI_LENGTH)
                            {
                                MXC_XiaZhi_VAVLE = 1;
                                MXC_cXiaZhiDelay = dwTickCount + MXC_PARAM_XIAZHI_TIME;                            
                            }
                        }
                    }
                    if(MXC_XiaChongMotorMode == 1)
                    {
                            AxisMoveTwoPos(Y_AXIS,MXC_XiaChongSpeed,2000,MXC_XiaChongLowSpeed,9999999,0);
                    }	
             }
    break;
    case 4:  //碰到右大微动,延时停
            if(MXC_XiaChong_IN_UP)
            {
                  MXC_cXiaChongDelay = dwTickCount + MXC_PARAM_XC_DELAY;
                  MXC_cXiaChongStep = 5;
                  MXC_LeftFenZhen_VAVLE = 0;  	//退左分针
                  MXC_RightFenZhen_VAVLE = 0;	//退右分针	
                  MXC_GouZhen_VAVLE = 1;
                  MXC_cGouZhenTime  = dwTickCount + 300;
            }
            else if(dwTickCount >= MXC_cXiaChongDelay) //自动停机
            {	
                  MXC_cXiaChongStep = 0;
//                  MXC_ShaChe_Output();////刹车
                  MXC_XiaChong_MOTOR = 0;// 	//下冲电机
                  MXC_SetAlarmCode(MXC_XC_ALARM);
                  MXC_LeftFenZhen_VAVLE = 0;   	//退左分针
                  MXC_RightFenZhen_VAVLE = 0;	//退右分针
                  AxisEgmStop(Y_AXIS);
            }
            
            break;
    case 5:	
            if(dwTickCount >= MXC_cXiaChongDelay)	
            {
                    
                    AxisEgmStop(Y_AXIS);
                    MXC_XiaChong_MOTOR = 0;      //延时刹车
                    if(MXC_PARAM_SC_MODE)
                    {
                        MXC_cXiaChongStep = 0;
                    }
                    else
                    {
                        MXC_cXiaChongStep = 6;
                    }			
            }
            break;
    case 6:	
            {
                    MXC_cXiaChongStep = 7;
                    MXC_cXiaChongDelay = dwTickCount + MXC_PARAM_SC_DELAY;		
            }
            break;
    case 7:
            if((dwTickCount >= MXC_cXiaChongDelay))
            {
                    MXC_cXiaChongStep = 8;
                    MXC_cXiaChongDelay = dwTickCount+ 150;
 //                   MXC_XC_SongZhou = MXC_SERVER_DISEN;  
                    MXC_XC_ShaChe   = MXC_SC_EN;
            }	
            break;
    case 8:
            if((dwTickCount >= MXC_cXiaChongDelay))
            {
                    MXC_cXiaChongStep = 0;
 //                   MXC_XC_SongZhou = MXC_SERVER_DISEN;  
                    MXC_XC_ShaChe   = MXC_SC_DISEN;
            }	
            break;
    case 20:                      // 点动普通下冲动作
  //              MXC_XC_SongZhou = MXC_SERVER_EN;
                MXC_XC_ShaChe   = MXC_SC_DISEN;
                MXC_cXiaChongDelay = dwTickCount + 50;	
                MXC_cXiaChongStep = 21;
            break;
    case 21:   
               if((dwTickCount >= MXC_cXiaChongDelay))
               {
                    MXC_XiaChong_MOTOR = 1;
                    MXC_cXiaChongDelay = dwTickCount + 50;	
                    MXC_cXiaChongStep = 22;
               }
            break;
    case 22:   
               if((dwTickCount >= MXC_cXiaChongDelay))
               {
                    MXC_XiaChong_MOTOR = 0;
              //      MXC_XC_SongZhou    = MXC_SERVER_EN;
                    
                    if(MXC_XiaChongMotorMode)
                        MXC_cXiaChongStep = 0;
                    else
                    {
                        MXC_XC_ShaChe   = MXC_SC_EN;
                        MXC_cXiaChongDelay = dwTickCount + 150;	
                        MXC_cXiaChongStep = 23;
                    }
               }
            break;
    case 23:   
               if((dwTickCount >= MXC_cXiaChongDelay))
               {
                    //MXC_XC_SongZhou    = MXC_SERVER_DISEN;   
                    MXC_XC_ShaChe   = MXC_SC_DISEN;
                    MXC_cXiaChongStep  = 0;
               }
            break;
    case 40:                      // 点动电机下冲动作
                //MXC_XC_SongZhou = MXC_SERVER_EN;
                MXC_cXiaChongDelay = dwTickCount + 50;	
                MXC_cXiaChongStep = 41;
            break;
    case 41:   
                if(!Y_DRV)AxisMovePos(Y_AXIS,20,10);
                MXC_cXiaChongStep = 42;
            break;
    case 42:   
           if(!Y_DRV)
           { 
                MXC_cXiaChongStep = 0;
           }
            break;
    }
}

 //分针
void  MXC_NiLongFenZhen(void)
{	
	//右分针
	switch(MXC_cRightFenZhenStep)
	{ 
            case 0:
                    break;
            case 1:
                        MXC_cFenZhenRightDelay = MXC_PARAM_R_FZ_DELAY+dwTickCount;
                        MXC_cRightFenZhenStep  = 2;
                    break;
            case 2:
                    if(dwTickCount >= MXC_cFenZhenRightDelay)
                    {
                        MXC_cRightFenZhenStep = 3;
                        MXC_RightFenZhen_VAVLE = 1;//右分针电磁阀
                        MXC_cFenZhenRightDelay = dwTickCount + MXC_FenZhengErrorTime;      	
                    }	
            break;
            case 3:  //碰到右大微动,延时停
                    if(!MXC_RightFenZhen_Origin_IN)   //右分针原点离开
                    {
                        MXC_cFenZhenRightDelay = dwTickCount + MXC_FenZhengErrorTime;
                        MXC_cRightFenZhenStep = 4;
                    }//右分针不下去
                    else if(dwTickCount >= MXC_cFenZhenRightDelay)
                    {
                         MXC_SetAlarmCode(MXC_RFZ_LIMIT_ALARM);			
                    }
                    break;
            case 4:	
                    if(MXC_RighttFenZhen_IN)  //插针到位
                    {
                        MXC_cRightFenZhenStep = 0;
                        MXC_cLeftFenZhenStep = 1;   //左分针延时启动
                    }
                    else if(dwTickCount >= MXC_cFenZhenRightDelay)
                    {
                            MXC_RightFenZhen_VAVLE = 0;//右分针
                            cRFengTimer++; 
                            //当右分针分不到位时，左分针也要重新分针
                            MXC_LeftFenZhen_VAVLE = 0;
                            MXC_cRightFenZhenStep = 0;
                            if(cRFengTimer < 4)
                            {
                                MXC_cRightFenZhenStep = 5;
                                MXC_cFenZhenRightDelay = dwTickCount + MXC_FenZhengErrorTime;
                            }
                            else
                            {
                                MXC_SetAlarmCode(MXC_RFZ_LIMIT_ALARM);		
                            }
                    }
                    break;
            case 5:	
                    if(MXC_RightFenZhen_Origin_IN)  //退到位
                    {
                        MXC_cRightFenZhenStep = 6;
                    }
                    else if(dwTickCount >= MXC_cFenZhenRightDelay)
                    {
                         MXC_SetAlarmCode(MXC_RFZ_ORIGIN_ALARM);	
                    }
                    break;
            case 6:
                    {
                         MXC_cRightFenZhenStep = 1;
                    }	
                    break;
	}
	//左分针
	switch(MXC_cLeftFenZhenStep)
	{ 
		case 0:
			break;
                case 1:
                        MXC_cFenZhenLeftDelay = MXC_PARAM_L_FZ_DELAY+dwTickCount;
                        MXC_cLeftFenZhenStep = 2;
                        break;
		case 2:
			if(dwTickCount >= MXC_cFenZhenLeftDelay)
			{
                            MXC_cLeftFenZhenStep = 3;
                            MXC_LeftFenZhen_VAVLE = 1; //左分针电磁阀
                            MXC_cFenZhenLeftDelay = dwTickCount + MXC_FenZhengErrorTime;      	
 			}	
        	break;
		case 3:  //离开左分针原点
			if(!MXC_LeftFenZhen_Origin_IN)   //左分针原点离开
			{
                            MXC_cFenZhenLeftDelay = dwTickCount + MXC_FenZhengErrorTime;
                            MXC_cLeftFenZhenStep = 4;
			}//左分针不下去
			else if(dwTickCount >= MXC_cFenZhenLeftDelay)
			{
			    MXC_SetAlarmCode(MXC_LFZ_LIMIT_ALARM);					
			}
			break;
		case 4:	
			if(MXC_LeftFenZhen_IN)  //插针到位
				MXC_cLeftFenZhenStep = 0;
			else if(dwTickCount >= MXC_cFenZhenLeftDelay)
			{
                            MXC_LeftFenZhen_VAVLE = 0;//左分针
                            cLFengTimer++; 
                            if(cLFengTimer < 6)
                            {
                                  MXC_cLeftFenZhenStep = 5;
                                  MXC_cFenZhenLeftDelay = dwTickCount + MXC_FenZhengErrorTime;
                                  if((cLFengTimer%2) == 0)
                                  {
                                      MXC_RightFenZhen_VAVLE = 0;
                                      MXC_cRightFenZhenStep = 0;
                                  }
                            }
                            else
                            {					
                                  MXC_SetAlarmCode(MXC_LFZ_LIMIT_ALARM);	
                            }
			}
			break;
		case 5:	
			if(MXC_LeftFenZhen_Origin_IN)  //退到位
			{
                            MXC_cLeftFenZhenStep = 6;
			}
			else if(dwTickCount >= MXC_cFenZhenLeftDelay)
			{
                             MXC_SetAlarmCode(MXC_LFZ_ORIGIN_ALARM);						
			}
			break;
		case 6:
                        if((cLFengTimer%2) == 0)  //左边插两次都插不到，就退右边再同时插
                        {
                            MXC_cRightFenZhenStep = 1;
                            cRFengTimer = 0;
                            MXC_cLeftFenZhenStep = 0;
                        }
                        else                         
                        {
                            MXC_cLeftFenZhenStep = 1;
                        }	
			break;
	}
}


#endif