GC23005/Machine/JuXingMachine/JXMXC_NiLong_StepJi.c

#include "global.h"

#if JU_XING_MACHINE

void MXC_NiLongXiuCiJiCheckStart(void);
void MXC_ShaChe_Output(void);
void MXC_NiLongXiuCiJi_Motor(void);
void MXC_NiLongXiuCiJi_XiaC(void);
void MXC_Start_FenZ(void);
void MXC_NiLongXiuCiJi_FenZhengProc(void);
void MXC_ChuiQiProc(void);
void MXC_JiaoDao(void);
void MXC_ManualAction(void);
void MXC_AutoAction(void);

unsigned char cLFengTimer,cRFengTimer,cGuZhangStop = 0;
unsigned long cShaCheTime,cLaLianLine,cGouZhenTime;
unsigned char cChuiQiStep = 0,cGouZhenResetOK;
unsigned short cBudaiCheckDelay = 0;
unsigned char bHandWork,bPulseTatol_EN,bFirst,cInt1_OK,cStopFlag,cOneTimes,cKey_Time;
long cSetEncode,cTotal,cDinWeiTime,cAddSetPulseNum,cEncodePulse,cWorkPulseNum;
unsigned long cZipperLength[2];
unsigned char cCheckLengthOk=0,cDaoJu_Flag=0;
unsigned char STOP_IN_FLAG,STOP_IN_FLAG_OLD,STOP_FILTER;
unsigned char MXC_SingOneFlag = 0;
unsigned char MXC_KD_Flag = 0,KD_GO_ON_FLAG = 0;
long MXC_KD_pos = 0,save_pos_buff = 0;

//故障报警
void MXC_SetAlarmCode(unsigned alarm_code)
{
    SetAlarmCode(MXC_ALARM_ADDR,alarm_code);
    MXC_bAlarmStop = 1;
}

//高速输入X31/X17外部色标信号中断
void MXC_ExtiActionX31(void)
{
     if(cSeBiaoEn && !cSeBiaoOk)
    {
        cSeBiaoOk = 1;
        cSeBiaoEn  = 0;
        if(X_DRV)SetRemainLength(X_AXIS, MXC_PARAM_SEBIAO_DW_LENGTH,MXC_PARAM_SB_OFFSET_SPEED);
    }
}

void MXC_ExtiActionX20(void)
{

}
void MXC_InitAction(void)
{
    float length_buff,pulse_buff;
    
    CalFreqTab_X_Free(25);
    length_buff = MXC_PARAM_DAILUN_LENGTH;
    pulse_buff  = 2000;
    XGearRatio  = pulse_buff/length_buff;

    MXC_XC_SongZhou = MXC_SERVER_EN;				 
    MXC_XIA_ZHI_ENABLE = 0; 
    
    MXC_TuoDaiSongZhou = MXC_SERVER_DISEN;
    
    if(MXC_XIA_ZHI_ENABLE)
       MXC_XiaZhi_MOTOR = 1;
    else	
       MXC_XiaZhi_MOTOR = 0;  
    
    STOP_IN_FLAG = STOP_IN;
    STOP_IN_FLAG_OLD = STOP_IN_FLAG;
}

void MXC_NiLongXiuCiJiAction(void)
{
    MXC_NiLongXiuCiJiCheckStart();  //启动
    MXC_NiLongXiuCiJi_FenZhengProc();	//左右分针
    MXC_NiLongXiuCiJi_XiaC();   //下冲
    MXC_ChuiQiProc();
    MXC_NiLongXiuCiJi_Motor();			//拖带控制
    MXC_JiaoDao();
    MXC_ManualAction();
    MXC_AutoAction();	
}


void MXC_ManualAction(void)
{
      long i;
           
      //清总产量
      if(MXC_bClear)         //清总产量
      {
          MXC_bClear = 0;
          ClrcToTal(MXC_TOTAL_ADDR);
          MXC_bSaveWorkData = 1;
      }

      //当长度改变时，生产总量自动清零
      if(MXC_bChangeLength)
      {
          MXC_bChangeLength = 0;
          MXC_bClear = 1;
      }
      //加10
      if(MXC_bAddLength)
      {
          MXC_bAddLength = 0;
          i = MXC_SET_REVISE_ZIPPER_LENGTH;
          i += 10;
          SetData32bits(MXC_ZIPPER_LENGTH_ADDR,i);
      }
      //减10
      if(MXC_bDecLength)
      {
          MXC_bDecLength = 0;
          i = MXC_SET_REVISE_ZIPPER_LENGTH;
          i -= 10;
          SetData32bits(MXC_ZIPPER_LENGTH_ADDR,i);		
      }
      //工作方式选择(数控定寸和勾针定寸)　
      if(MXC_bSetDCMode)
      {
          MXC_bSetDCMode = 0;
          if(!MXC_bRunning)
          {
                  MXC_DC_MODE++;
                  if(MXC_DC_MODE > 2)MXC_DC_MODE = 0;
          
                  if(MXC_DC_MODE != 0)	
                  {
                      MXC_GouZhen_VAVLE = 1;	
                      MXC_XIA_ZHI_ENABLE = 0;	
                      MXC_XiaZhi_MOTOR = 0;  
                  }
          }
      }
      //勾针方式选择(活动勾针和固定勾针)　
      if(MXC_bChangeGouZhenMode)
      {
          MXC_bChangeGouZhenMode = 0;
          if(!MXC_bRunning)
          {
                  MXC_GOU_ZHEN_MODE++;
                  if(MXC_GOU_ZHEN_MODE > 1)MXC_GOU_ZHEN_MODE = 0;	
          }
      }
      //下止工作选择)　
      if(MXC_bChangeXiaZhiMode)
      {
          MXC_bChangeXiaZhiMode = 0; 
          if(!MXC_bRunning)
          {
                  MXC_XIA_ZHI_ENABLE++;
                  if(MXC_XIA_ZHI_ENABLE > 1)MXC_XIA_ZHI_ENABLE = 0;
                  
                  if(MXC_XIA_ZHI_ENABLE)
                     MXC_XiaZhi_MOTOR = 1;
                  else	
                     MXC_XiaZhi_MOTOR = 0;   	
          }
      }
      
      if(MXC_bJiaoDao)
      {
          MXC_cJiaoDaoStep = 1;
          MXC_bJiaoDao = 0;
      }
      
      if(MXC_bChuiQi)
      {
          MXC_bChuiQi = 0;
          
          if(MXC_cChuiQiStep == 0)MXC_cChuiQiStep = 1;
      }
      
    if((MXC_bRunning) == 0) ////手动 
    {        
        if(MXC_ManXiaChong_UP || MXC_bXiaChong)   
        {
            MXC_bXiaChong = 0;
            if(MXC_cXiaChongStep == 0)MXC_cXiaChongStep = 1;
        }
        
        if(MXC_cXiaChongStep == 0)
        {
            if(MXC_bLeftFenZhen)
            {
                MXC_bLeftFenZhen      = 0;
                MXC_LeftFenZhen_VAVLE = ~MXC_LeftFenZhen_VAVLE;
            }

            
            if(MXC_bRightFenZhen)
            {
                MXC_bRightFenZhen     = 0;
                MXC_RightFenZhen_VAVLE= ~MXC_RightFenZhen_VAVLE;
            }
            
                            //点动下冲
            if((MXC_bDotXiaChong))
            {
                MXC_bDotXiaChong = 0;
                if(MXC_LeftFenZhen_IN && MXC_RighttFenZhen_IN)
                {
                    if(MXC_XiaChongMotorMode == 0)
                    {
                        if(MXC_cXiaChongStep == 0)MXC_cXiaChongStep = 20;
                    }
                    else
                    {
                        if(MXC_cXiaChongStep == 0)MXC_cXiaChongStep = 40;
                    }	
                }
                else
                {
                  MXC_SetAlarmCode(MXC_XIA_CHONG_ALARM);		//下冲条件不满足
                }
            }
            
              if(MXC_bGouZhen)
              {
                  MXC_bGouZhen = 0;
                  if((MXC_GOU_ZHEN_MODE == 0))//普通勾针（活动）过链
                  {
                      MXC_cGouZhenTime  = dwTickCount + 300;
                      MXC_GouZhen_VAVLE = ~MXC_GouZhen_VAVLE;	
                  }
                  else	//固定勾针
                  {
                      MXC_GuDingGouZhen = ~MXC_GuDingGouZhen;
                  }			
              }
        }
          
        if(MXC_DC_MODE != 0)   //伺服定寸
        {      
            MXC_GuDingGouZhen = 1;
            MXC_GouZhen_VAVLE = 1;
        }
        else if((MXC_GOU_ZHEN_MODE == 0) )//普通勾针（活动）过链
        {
            if(dwTickCount >= MXC_cGouZhenTime) MXC_GouZhen_VAVLE = 0;
        }
        else
        {
            if(MXC_XiaMode)     //0普通下止，1超声下止
            {
                if(MXC_GuoLian_IN_UP)
                {
                    MXC_GuDingGouZhen = 0;	
                }
            }
            else	//刘铁方式(下拉一下就可以复位)
            {
                if(dwTickCount >= MXC_cGouZhenTime) MXC_GuDingGouZhen = 0;	
            }
        }		
        //下止动作
        if(MXC_XiaZhi_IN_UP || MXC_bXiaZhi)
        {
            MXC_bXiaZhi = 0;
            if(MXC_XiaZhi_VAVLE)
            {
                MXC_XiaZhi_VAVLE = 0;
                MXC_ChaoSheng = 0;
                MXC_FenDai_VAVLE = 0;		//分带输出
            }	
            else
            {
                if(MXC_XiaZhi_IN || MXC_XIA_ZHI_ENABLE)  //下止选择
                {	
                    //下止输出
                     MXC_cXiaZhiDelay = dwTickCount + MXC_PARAM_XIAZHI_TIME;
                     MXC_XiaZhi_VAVLE = 1;
                }
            }
        }	
        else if(MXC_XiaZhi_IN_DW)
        {
            MXC_XiaZhi_VAVLE = 0;		//下止电磁阀
            MXC_ChaoSheng    = 0;		//超声输出	
            MXC_FenDai_VAVLE = 0;		//分带输出
        }					
 
        if(MXC_bChuDai)
        {
            MXC_ChuDai_VAVLE = 1;		
        }
        else
        {
            MXC_ChuDai_VAVLE = 0;
        }	
    }
    
    if((MXC_XiaMode != 0))//普通下止
    {
        if(MXC_GuoLian_IN_UP|| MXC_FenDai_IN_UP)MXC_FenDai_VAVLE = 1; 
        if(MXC_bRunning)
        {	
            if(MXC_GuoLian_IN_UP && MXC_XiaZhi_VAVLE)MXC_cXiaZhiDelay = dwTickCount + 10 * MXC_PARAM_XIAZHI_DELAY_TIME;	
            if(MXC_GuoLian_IN && MXC_XiaZhi_VAVLE)
            {
                if(!MXC_ChaoSheng && (dwTickCount >= MXC_cXiaZhiDelay))
                {
                    MXC_ChaoSheng = 1;
                    MXC_cXiaZhiDelay = dwTickCount + (unsigned long)10 * MXC_PARAM_CHAOSHENG_TIME;	
                }
                if(MXC_ChaoSheng && (dwTickCount >= MXC_cXiaZhiDelay))
                {
                    MXC_FenDai_VAVLE = 0;		//分带输出
                    MXC_ChaoSheng    = 0;		//超声输出
                    MXC_XiaZhi_VAVLE = 0;		//下止阀
                }
            }
        }		
    }
    else 
    { 
            //下止下冲电磁铁
        if((MXC_XiaZhi_VAVLE != 0) && (dwTickCount >= MXC_cXiaZhiDelay)) 
        {       
            MXC_XiaZhi_VAVLE = 0;
        }	
    }
}

void MXC_AutoAction(void)
{
    DISPLAY_DATA0 = MXC_cAutoStep;
    DISPLAY_DATA1 = MXC_cMotorStep;
    DISPLAY_DATA2 = MXC_cLeftFenZhenStep;
    DISPLAY_DATA3 = MXC_cRightFenZhenStep;
    DISPLAY_DATA4 = MXC_cXiaChongStep;
    DISPLAY_DATA5 = dwRealPos;
    if(MXC_bRunning)
    {   
        if(MXC_XiaZhi_IN || (!MXC_Zipper_IN))
            MXC_ChuDai_VAVLE = 0;	  	
        else
            MXC_ChuDai_VAVLE = 1;
        
        if((MXC_DC_MODE == 0) && (MXC_GOU_ZHEN_MODE == 0))
        { 	
            if(MXC_GouZhen_IN_UP)MXC_cGouZhenTime = 1;
        }
        else
            MXC_cGouZhenTime = 1;	
        
        switch(MXC_cAutoStep)
        {
            case 0:
                    break;
            case 1:
                    if(dwTickCount >= MXC_cAutoDelay)
                    {
                        if(MXC_TuoDaiSongZhou == MXC_SERVER_DISEN)
                        {
                            MXC_TuoDaiSongZhou = MXC_SERVER_EN;
                            MXC_cAutoDelay = dwTickCount + 200;   //先锁轴 
                        }
                        else
                            MXC_cAutoDelay = dwTickCount;
                         MXC_cAutoStep = 2;
                    }
                    break;
            case 2:
                    //左右分针要退到位，过链到位要离开
                    if(!MXC_GouZhen_IN && MXC_LeftFenZhen_Origin_IN && MXC_RightFenZhen_Origin_IN && !MXC_LeftFenZhen_IN && !MXC_RighttFenZhen_IN && (dwTickCount >= MXC_cAutoDelay))
                    {
                        MXC_cAutoStep = 3;
                        MXC_cMotorStep = 1;   //启动拖带 
                    }     			
                    break;
            case 3:
                    //拖带已经完成
                    if(MXC_cMotorStep == 0)
                    {
                         if(SingOneFlg)
                        {
                            dwZipCnt   = 0;
                            SingOneFlg = 0;
                            MXC_cAutoStep = 0;
                            MXC_bRunning = 0;
                        }
                        else
                        {
                            MXC_cAutoStep = 4;
                        }
                    }
                    break;	
            case 4:
                        MXC_cAutoStep = 5;
                    break;
            case 5:
                    //左右分针都已完成
                    if((MXC_cLeftFenZhenStep == 0) && (MXC_cRightFenZhenStep == 0))
                    {
                        MXC_cXiaChongStep = 1;   //下冲电机启动
                        MXC_cAutoStep = 6;	
                    }
                    break;
            case 6:  //下冲已完成
                    if(MXC_cXiaChongStep == 0)
                    {
                        dwZipCnt++;
                        AddToTal(MXC_TOTAL_ADDR);	 //计数增加和保存
                        CalProSP(MXC_PROSPEED_ADDR);
                        MXC_cAutoStep = 7;                        
                    }
                    break;		
            case 7:
                    if(MXC_LeftFenZhen_Origin_IN && MXC_RightFenZhen_Origin_IN && !MXC_LeftFenZhen_IN && !MXC_RighttFenZhen_IN)
                    {
                        if(GetTotal(MXC_TOTAL_ADDR) >= MXC_SET_TOTAL)MXC_SetAlarmCode(MXC_TOTAL_ALARM);
                        
                        MXC_cAutoStep = 8;
                    }
                    break;	
            case 8:
                        MXC_cAutoDelay = dwTickCount + MXC_PARAM_MOTOR_DELAY;
                        
                        if(MXC_SingOneFlag)
                        {
                            dwZipCnt   = 0;
                            MXC_SingOneFlag = 0;
                            MXC_cAutoStep = 0;
                            MXC_bRunning = 0;
                        }
                        MXC_cAutoStep = 1;	
                    break;		                     
        }		         
    }
}

// 检测是否踏了脚踏开关
void MXC_NiLongXiuCiJiCheckStart(void)
{
    //  停止键        不能在工作,手动,停止过程中                                
    if((MXC_bRunning == 0) && (START_IN_UP || MXC_bStart || MXC_bNext))
    {
        if(!MXC_LeftFenZhen_Origin_IN)MXC_SetAlarmCode(MXC_START_LFZ_ORIGIN_ALARM);	//没拉链
        else if(GetTotal(MXC_TOTAL_ADDR) >= MXC_SET_TOTAL)MXC_SetAlarmCode(MXC_TOTAL_ALARM);
        else if(!MXC_RightFenZhen_Origin_IN)MXC_SetAlarmCode(MXC_START_RFZ_ORIGIN_ALARM);
        else if(!MXC_Zipper_IN)MXC_SetAlarmCode(MXC_START_NO_ZIPPER_ALARM);
        else if((MXC_PARAM_SEBIAO_DW_LENGTH > MXC_SET_ZIPPER_LENGTH) && (MXC_DC_MODE==2))MXC_SetAlarmCode(MXC_SEBIAO_ZIPPER_LENGTH_ALARM);
        else if(MXC_KaDai_IN)MXC_SetAlarmCode(MXC_KA_DAI_ALARM);
        else
    	{
            if(MXC_bNext)
            {
               SingOneFlg = 1;   
               MXC_bNext  = 0;
            }
            MXC_bRunning = 1;
            MXC_cAutoStep = 1;	              
            cGouZhenTime = 1;   
            cCheckLengthOk = 0;
            cZipperLength[0] = 0;			
            cZipperLength[1] = 0;
            dwZipCnt = 0;
    	}
    	MXC_bStart = 0;
    }

	//卡带感应
    if(MXC_KaDai_IN && (dwTickCount >= MXC_cKaDaiDelay))
    {
        if(MXC_DC_MODE == 1)
        {
            if(X_DRV && MXC_bRunning && (MXC_cMotorStep == 20))
            {
                MXC_KD_Flag = 1;
                KD_GO_ON_FLAG = 1;
            }
        }
        MXC_SetAlarmCode(MXC_KA_DAI_ALARM);
        
        
	MXC_cKaDaiDelay = dwTickCount + 2200;
    }
    
    if(MXC_KD_Flag)
    {      
        if(!X_DRV)
        {
            MXC_KD_pos  = dwRealPos - save_pos_buff;
            MXC_KD_Flag = 0;
        }
    }
    
    if(MXC_KaDai_IN_UP)
    {
        if(MXC_cChuiQiStep == 0)MXC_cChuiQiStep = 1;
    }		
 //停止
   STOP_IN_FLAG_OLD = STOP_IN_FLAG;
    
   if(STOP_IN)
   {
       if(STOP_FILTER < 50)
       {
           STOP_FILTER++;
       }
       else
           STOP_IN_FLAG = 1;
   }
   else if(STOP_FILTER > 25)
   {
       STOP_FILTER--;
   }
   else
       STOP_IN_FLAG = 0;
   
    if(MXC_bStop)
    {
        MXC_bStop = 0;
        if(MXC_bRunning)MXC_SingOneFlag = 1;
    }
    
    
   
    if(((STOP_IN_FLAG && !STOP_IN_FLAG_OLD)))
    { 
        MXC_bStop = 0;
        if(MXC_bRunning)
        {
           if(MXC_cXiaChongStep==0)
           {
              if(MXC_cChuiQiStep == 0)MXC_cChuiQiStep = 1;
              
              if(!MXC_XiaChong_MOTOR)MXC_XC_SongZhou = MXC_SERVER_DISEN;           
           }
           
            MXC_bRunning = 0;  
            cStopFlag = 0;
            MXC_cAutoStep = 0;
            MXC_cMotorStep = 0;
            MXC_cDCPStep   = 0;
            AxisDecStop(X_AXIS);
            MXC_cJiaoDaoStep = 0;
            SingOneFlg    = 0;
            MXC_SingOneFlag = 0;
            MXC_KD_Flag     = 0;
            KD_GO_ON_FLAG   = 0;
        }
        else
        {
            MXC_bRunning = 0;
                    
            cStopFlag = 0;
            MXC_cAutoStep = 0;
            MXC_cMotorStep = 0;
            MXC_cXiaChongStep = 0;
            MXC_cLeftFenZhenStep = 0;
            MXC_cRightFenZhenStep = 0;
            MXC_cJiaoDaoStep = 0;
            MXC_cDCPStep  = 0;
            MXC_XiaZhi_VAVLE     = 0;
            MXC_LeftFenZhen_VAVLE = 0;
            MXC_RightFenZhen_VAVLE = 0;
            MXC_XiaChong_MOTOR   = 0;
            MXC_ChaoSheng        = 0;
            MXC_JiaoDao_OUT      = 0;
            MXC_FenDai_VAVLE     = 0;
            MXC_ChuDai_VAVLE     = 0;
            MXC_GuDingGouZhen    = 0;  
            SingOneFlg    = 0;
            MXC_SingOneFlag = 0;
            MXC_KD_Flag     = 0;
            KD_GO_ON_FLAG   = 0;
            if(MXC_XiaChongMotorMode)
                MXC_XC_SongZhou = MXC_SERVER_DISEN;  
            else
                MXC_XC_ShaChe   = MXC_SC_DISEN;
           
           if((MXC_cChuiQiStep == 0) &&(MXC_cXiaChongStep==0))MXC_cChuiQiStep = 1;      
           AxisDecStop(X_AXIS);
           SetAlarmCode(MXC_ALARM_ADDR,MXC_NO_ALARM);
        }
    }
    
    if(!MXC_bRunning && (MXC_cMotorStep==0) && (MXC_cXiaChongStep == 0))
    { 
      if(!X_DRV)MXC_TuoDaiSongZhou = MXC_SERVER_DISEN;	 
    }
    if(MXC_bAlarmStop)
    {
        MXC_bAlarmStop = 0;
        MXC_bRunning = 0;
        MXC_cAutoStep = 0;
        MXC_cMotorStep = 0;
        MXC_cLeftFenZhenStep = 0;
        MXC_cRightFenZhenStep = 0; 
        MXC_cDCPStep          = 0;
        MXC_LeftFenZhen_VAVLE = 0;
        MXC_RightFenZhen_VAVLE = 0;
        MXC_SingOneFlag        = 0;
        AxisDecStop(X_AXIS);     
        if((GetAlarmCode(MXC_ALARM_ADDR) == MXC_XIA_CHONG_ALARM) || (GetAlarmCode(MXC_ALARM_ADDR) == MXC_XC_ALARM) || (GetAlarmCode(MXC_ALARM_ADDR) == MXC_FEN_ZHEN_ALARM))
        {
            MXC_cXiaChongStep = 0;
            MXC_XiaChong_MOTOR = 0;
        }
    }
}   

void MXC_JiaoDao(void)
{
   if(MXC_cJiaoDaoStep == 1)
    {
        MXC_cChuiQiDelay = dwTickCount + 500;
        MXC_JiaoDao_OUT = 1;
        MXC_cJiaoDaoStep = 2;
    }
    else if((MXC_cJiaoDaoStep == 2) && (dwTickCount >= MXC_cChuiQiDelay)) 
    {
        MXC_JiaoDao_OUT = 0;	
        MXC_cJiaoDaoStep = 0;
    }  	
}



void MXC_ChuiQiProc(void)
{	
      //吹气
    if(MXC_XiaChong_IN_UP)
    {
        if(MXC_cChuiQiStep == 0)MXC_cChuiQiStep = 1;
    }
    
    
    switch (MXC_cDCPStep)
    {
        case 0:
        break;
        case 1:
             MXC_cDCPStep = 2;
             MXC_cDaoJuCheckDelay = dwTickCount + ERRORTIME;
        break;
        case 2:
             if(MXC_DingChuPian_IN_DW)
             {
                  MXC_cDCPStep = 0;
             }
             else if(dwTickCount >= MXC_cDaoJuCheckDelay)MXC_SetAlarmCode(MXC_DAO_JU_ALARM);         
        break;
    }
    
    switch(MXC_cChuiQiStep)
    {
        case 1:
            MXC_cChuiQiStep = 2;
            if(MXC_bRunning)MXC_cChuiQiDelay = dwTickCount+MXC_PARAM_DELAY_CHUIQI_TIME;            
        break;
        case 2:
            if(dwTickCount >= MXC_cChuiQiDelay)
            {
                MXC_cChuiQiDelay = dwTickCount + MXC_PARAM_CHUIQI_TIME;	
                MXC_ChuiQi_VAVLE = 1;//
                MXC_cDCPStep = 1;
                MXC_cChuiQiStep = 3;                
            }
        break;
        case 3:
            if(dwTickCount >= MXC_cChuiQiDelay)
            {
                MXC_ChuiQi_VAVLE = 0;//
                MXC_cChuiQiStep = 0;
            }
        break;
    }
}
void MXC_ShaChe_Output(void)
{
    //启动吹气
    cShaCheTime = dwTickCount + (unsigned long)120;
    if(MXC_XiaChongMotorMode == 0)MXC_XC_SongZhou = MXC_SERVER_EN;
}

void MXC_Output_XiaCi(void)//下止输出
{
	if(MXC_XiaZhi_IN || MXC_XIA_ZHI_ENABLE)  //下止选择
	{	
            //下止输出
             MXC_cXiaZhiDelay = dwTickCount + 10 * MXC_PARAM_XIAZHI_TIME;
             MXC_XiaZhi_VAVLE = 1;
	}	
}
//关下止动作
void MXC_Close_XiaCi(void)
{
	if((MXC_XiaMode != 0))//普通下止
	{
		if(MXC_GuoLian_IN_UP || MXC_FenDai_IN_UP)
			MXC_FenDai_VAVLE = 1; 
		if(MXC_bRunning)
		{	
                    if(MXC_GuoLian_IN_UP && MXC_XiaZhi_VAVLE)
                    {
                        MXC_cXiaZhiDelay = dwTickCount + 10 * MXC_PARAM_XIAZHI_DELAY_TIME;	
                    }
                    if(MXC_GuoLian_IN && MXC_XiaZhi_VAVLE)
                    {
                        if(!MXC_ChaoSheng && (dwTickCount >= MXC_cXiaZhiDelay))
                        {
                                MXC_ChaoSheng = 1;
                                MXC_cXiaZhiDelay = dwTickCount + (unsigned long)10 * MXC_PARAM_CHAOSHENG_TIME;	
                        }
                        if(MXC_ChaoSheng && (dwTickCount >= MXC_cXiaZhiDelay))
                        {
                                MXC_FenDai_VAVLE = 0;		//分带输出
                                MXC_ChaoSheng    = 0;		//超声输出
                                MXC_XiaZhi_VAVLE = 0;		//下止阀
                        }
                    }
		}		
	}
	else 
	{ 
                //下止下冲电磁铁
            if((MXC_XiaZhi_VAVLE != 0) && (dwTickCount >= MXC_cXiaZhiDelay)) 
            {       
                MXC_XiaZhi_VAVLE = 0;
            }	
	}		
}




unsigned char ComPareLength(void)
{
	if((cZipperLength[0] != 0) && (cZipperLength[1] != 0))
    {
		if(cZipperLength[0] > cZipperLength[1])
		{
		    if((cZipperLength[0] - cZipperLength[1]) > 200)
			{
			    return 0;
			}
			else 
			    return 1;
		}
		else
	    {
		    if((cZipperLength[1] - cZipperLength[0]) > 200)
			{
			    return 0;	
			}
			else
			    return 1;
		}
	}
	else 
	    return 0;
}

void  MXC_NiLongXiuCiJi_Motor(void)
{
        static long save_buff,gou_zhen_buff,zipper_length_buff;
	static unsigned long zipper_length;
        short *revise_buff;
        
        DISPLAY_DATA6 = zipper_length;
        if(MXC_bRunning)
        {
            if(MXC_Zipper_IN)
            {
                MXC_cBudaiCheckDelay = dwTickCount + MXC_PARAM_MOTOR_ALARM_TIME;		
            }
            else if(dwTickCount >= MXC_cBudaiCheckDelay)	//没布带了
            {
                MXC_SetAlarmCode(MXC_NO_ZIPPER_ALARM);	//没拉链
            }              
        }
 
        dwRealPos = GetPos(X_AXIS);
	switch(MXC_cMotorStep)
	{
		case 0:
                break;
	   //         过链         左分针退位  左到位
		case 1: if(MXC_LeftFenZhen_Origin_IN && (!MXC_LeftFenZhen_IN) && MXC_RightFenZhen_Origin_IN && (!MXC_RighttFenZhen_IN)) 
                {
                         save_buff  = dwRealPos;       
                         revise_buff = &user_datas[17];
                         save_pos_buff = dwRealPos;
                        if(MXC_DC_MODE == 0)                 //钩针定寸
                        {
                            if(MXC_DEC_MODE) //数控模式
                            {	
                               if(MXC_PARAM_AUTO_CHECK_MODE)
                               {
                                   if(cCheckLengthOk)
                                   {
                                       MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_SET_SPEED,1,5,1);                            
                                   }
                                   else
                                   {
                                        if(cCheckLengthOk == 0)
                                        {
                                            cZipperLength[0] = cZipperLength[1];			
                                            cZipperLength[1] = zipper_length_buff - dwRealPos;
                                            zipper_length_buff = dwRealPos;
                                            if(ComPareLength())
                                            {
                                                cCheckLengthOk = 1;
                                            }
                                        }

                                       if(cCheckLengthOk)zipper_length =  cZipperLength[1] + (*revise_buff);
                                       MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_FIRST_SPEED,1,5,1);                                
                                   }
                               }
                               else
                               {
                                   zipper_length = MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH;
                                   if(dwZipCnt==0) MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_FIRST_SPEED,1,5,1); 
                                   else
                                     MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_SET_SPEED,1,5,1);
                               }
                            }	
                            else //  感应方式
                            {
                                AxisContinueMove(X_AXIS,MXC_PARAM_SET_SPEED,MXC_DIR_P);                               
                            }
                            MXC_cMotorStep = 2;
                        }
                        else if(MXC_DC_MODE == 1)   //电机定寸
                        {        
                            if(KD_GO_ON_FLAG)
                            {
                                if(MXC_KD_pos > (MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH))                                 
                                    zipper_length = MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH;
                                else
                                    zipper_length = MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH - MXC_KD_pos;
                                KD_GO_ON_FLAG = 0;
                            }
                            else
                               zipper_length = MXC_SET_ZIPPER_LENGTH + (*revise_buff) + MXC_PARAM_DAOKOU_LENGTH;
                            
                            MXC_cMotorStep = 20;
                            MXC_GouZhen_VAVLE = 1;			 //定位(活动勾针)电磁阀
                            MXC_GuDingGouZhen = 1;			 //定位(活动勾针)电磁阀
                            
                            AxisMovePosAccDec(X_AXIS,MXC_PARAM_SET_SPEED,zipper_length,1,5,1);
                        }
                        else                    //色标定寸
                        {
                             zipper_length = MXC_SET_ZIPPER_LENGTH + (*revise_buff);
                             
                             if((dwZipCnt==0)||SingOneFlg)MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_SB_LOW_SPEED,1,5,1);   
                             else MoveAction_Const_AccDec(X_AXIS,MXC_DIR_P,MXC_PARAM_SB_HIGH_SPEED,1,5,1);   
                             
                             cSeBiaoOk = 0;
                             cSeBiaoEn = 0;  
                             MXC_cMotorStep = 50;                           
                        }     
                        MXC_cGouZhenTime = dwTickCount + MXC_PARAM_GZ_DELAY;
                        MXC_cMotorDelay = dwTickCount +  MXC_MOTOR_ALALRM_TIME;
                }
                break;
		// step2-5  活动勾针定寸		
		case 2:
                        if((dwTickCount >= MXC_cGouZhenTime)&&(MXC_PARAM_GZ_RESET_MODE==0))MXC_GouZhen_VAVLE = 0;
                        if(MXC_DEC_MODE)   // 数控方式
                        {
                            if(MXC_PARAM_AUTO_CHECK_MODE)
                            {
                                if(cCheckLengthOk)
                                {
                                    if(((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_GZ_LENGTH))&&MXC_PARAM_GZ_RESET_MODE)MXC_GouZhen_VAVLE = 0;
                                    
                                    if((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_LOWSPEED_LENGTH))
                                    {    
                                        AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                                        MXC_cMotorStep = 3; 
                                    }    
                                }
                                else
                                {
                                     if(MXC_GouZhen_IN)
                                    {
                                        MXC_GouZhen_VAVLE = 0;
                                        MXC_cMotorStep = 4;
                                        AxisEgmStop(X_AXIS);     
                                    }  
                                    else
                                    {
                                        if(dwTickCount >= MXC_cGouZhenTime)MXC_GouZhen_VAVLE = 0;
                                         MXC_cMotorStep = 3; 
                                    }                                    	
                                }
                                
                            }
                            else
                            {
                                if(dwZipCnt==0)
                                {
                                    if(MXC_GouZhen_IN)
                                    {
                                        MXC_GouZhen_VAVLE = 0;
                                        MXC_cMotorStep = 4;
                                        AxisEgmStop(X_AXIS);     
                                    }  
                                    else
                                    {
                                        if(dwTickCount >= MXC_cGouZhenTime)MXC_GouZhen_VAVLE = 0;
                                         MXC_cMotorStep = 3; 
                                    }  
                                }
                                else
                                {
                                    if(((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_GZ_LENGTH))&&MXC_PARAM_GZ_RESET_MODE)MXC_GouZhen_VAVLE = 0;
                                    
                                    if((save_buff -dwRealPos) >= (zipper_length - MXC_PARAM_LOWSPEED_LENGTH))
                                    {    
                                        AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                                        MXC_cMotorStep = 3; 
                                    }                                  
                                }
                            }
                        }
                        else               // 感应方式
                        {
                            if(MXC_Dec_IN_DW)
                            {
                                AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                                MXC_cGouZhenTime = dwTickCount + MXC_PARAM_GZ_DELAY;
                                MXC_cMotorStep = 3;              
                            }  
                        }
                        if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;	
		case 3:    
                        if((dwTickCount >= MXC_cGouZhenTime)&&(MXC_PARAM_GZ_RESET_MODE==0))MXC_GouZhen_VAVLE = 0;
                        if(MXC_DEC_MODE)   // 数控方式
                        {
                            if(MXC_PARAM_AUTO_CHECK_MODE)
                            {
                                if(((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_GZ_LENGTH))&&MXC_PARAM_GZ_RESET_MODE &&cCheckLengthOk)MXC_GouZhen_VAVLE = 0;
                            }
                            else
                            {
                                if(((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_GZ_LENGTH))&&MXC_PARAM_GZ_RESET_MODE)MXC_GouZhen_VAVLE = 0;
                            }
                            
                            if(MXC_GouZhen_IN)
                            {
                                MXC_GouZhen_VAVLE = 0;
                                MXC_cMotorStep = 4;
                                AxisEgmStop(X_AXIS);     
                            }   
                        }
                        else               // 感应方式
                        {
                            MXC_cMotorStep = 4;                                        
                        }
                        
                        if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;
		case 4:	
                        if((dwTickCount >= MXC_cGouZhenTime)&&(MXC_PARAM_GZ_RESET_MODE==0))MXC_GouZhen_VAVLE = 0;
                        if(MXC_DEC_MODE)   // 数控方式
                        {
                            if(!X_DRV)
                            {
                                MXC_cMotorStep = 0;  
                            }                             
                        }
                        else               // 感应方式
                        {
                            if(MXC_GouZhen_IN)
                            {
                                MXC_cMotorStep = 5;
                                AxisEgmStop(X_AXIS);     
                            }
                        }  
                        if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;		
		case 5:	
                        if(MXC_DEC_MODE)   // 数控方式
                        {
                          
                        }
                        else               // 感应方式
                        {
                            if(!X_DRV)
                            {
                                MXC_cMotorStep = 0;  
                            } 
                        }   
                        if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);
                        break;	
		case 11://以下为固定勾针方式
                        if(MXC_XiaMode == 0)			//0　普通下止　1　超声下止 当超声下时勾针
                        {	
                            if(dwTickCount >= MXC_cAutoDelay)MXC_GuDingGouZhen = 0;
                            if(!MXC_GuoLian_IN)
                            {
                                AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                                MXC_cMotorStep = 12;
                                MXC_cAutoDelay = dwTickCount + (unsigned long)1500;   //延时检测	
                            }								
                        }
                        else
                        {	
                            if(MXC_GuoLianCheckMode)
                            {
                                if(!MXC_GuoLian_IN)
                                {
                                    AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                                    MXC_cMotorStep = 12;
                                    MXC_cAutoDelay = dwTickCount + (unsigned long)user_datas[12];   //延时检测                                 
                                }
                            }
                            else
                            {
                                if(MXC_GuoLian_IN)
                                {
                                    AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                                    MXC_cMotorStep = 12;
                                    MXC_cAutoDelay = dwTickCount + (unsigned long)user_datas[12];   //延时检测                                 
                                }                            
                            }
                        }		
                        break;
		case 12:
                        if(dwTickCount >= MXC_cAutoDelay)
                        {
                            if(MXC_GuDingGouZhen)
                            {	
                                MXC_GuDingGouZhen = 0;
                                MXC_cAutoDelay = dwTickCount + (unsigned long)1500;   //延时检测
                            }	
                            else if(!MXC_GuDingGouZhen)
                            {
                             //   MXC_SetAlarmCode(MXC_GU_DING_GOUZHEN_ALARM);
                            }			
                        }
                        
                        if(MXC_XiaMode == 0)			//0　普通下止　1　超声下止 当超声下时勾针	
                        {
                            if(MXC_GuoLian_IN)
                            {
                                MXC_GuDingGouZhen = 0;
                                MXC_cMotorStep = 13;
                                MXC_cAutoDelay = dwTickCount + (unsigned long)user_datas[10];   //延时停电机	
                            }	                             
                        }
                        else
                        {
                            if(MXC_GuoLianCheckMode)
                            {
                                if(MXC_GuoLian_IN_UP)
                                {
                                    MXC_GuDingGouZhen = 0;
                                    MXC_cMotorStep = 13;
                                    MXC_cAutoDelay = dwTickCount + (unsigned long)user_datas[10];   //延时停电机	
                                }
                            }
                            else 
                            {
                                if(MXC_GuoLian_IN_DW)
                                {
                                    MXC_GuDingGouZhen = 0;
                                    MXC_cMotorStep = 13;
                                    MXC_cAutoDelay = dwTickCount + (unsigned long)user_datas[10];   //延时停电机	
                                }                           
                            }	
                        }
                        break;	
		case 13:
                        if((dwTickCount >= MXC_cAutoDelay))	
                        {
                            if(MXC_XiaMode == 0)			//0　普通下止　1　超声下止 当超声下时勾针	
                            {
                                AxisEgmStop(X_AXIS);
                                if(MXC_GuoLian_IN)
                                {
                                    MXC_cMotorStep = 0;
                                    MXC_LIHE_VAVLE = 0;
                                }
                            }
                            else
                            {
                                if(MXC_GuoLianCheckMode)
                                {
                                    if(MXC_GuoLian_IN)
                                    {
                                        MXC_cMotorStep = 0;
                                        AxisEgmStop(X_AXIS);
                                        MXC_LIHE_VAVLE = 0;
                                    }
                                }
                                else
                                {
                                    if(!MXC_GuoLian_IN)
                                    {
                                        MXC_cMotorStep = 0;
                                        AxisEgmStop(X_AXIS);
                                        MXC_LIHE_VAVLE = 0;
                                    }                                
                                }	
                            }	
                        }						
                        break;
		
		//伺服定寸	
		case 20:
                        if(!X_DRV)MXC_cMotorStep = 0;
                        else if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_LONG_TIME_NO_ZIPPER_ALARM);                
                        break;
		case 50:
                        if(dwZipCnt==0)
                        {
                            cSeBiaoOk = 0;
                            cSeBiaoEn = 1;  
                            MXC_cMotorStep   = 51;
                        }
                        else
                        {
                            if((save_buff - dwRealPos + MXC_PARAM_LOWSPEED_LENGTH) >= (zipper_length  -MXC_PARAM_SEBIAO_DW_LENGTH)) AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                            if((save_buff - dwRealPos + MXC_PARAM_SEBIAO_TQ_LENGTH) >= (zipper_length - MXC_PARAM_SEBIAO_DW_LENGTH))
                            {
                                cSeBiaoOk = 0;
                                cSeBiaoEn = 1; 
                                MXC_cMotorStep   = 51;
                            }
                            else if((dwRealPos - save_buff) > (zipper_length + MXC_ERROR_LENGTH))MXC_SetAlarmCode(MXC_NO_SEBIAO_ALARM);
                            
                        }                        
                        break;	
		case 51:
                        if(dwZipCnt!=0)
                        {
                            if((save_buff - dwRealPos) >= (zipper_length - MXC_PARAM_LOWSPEED_LENGTH)) AxisChangeSpeed(X_AXIS,MXC_PARAM_LOW_SPEED);
                            if((save_buff - dwRealPos) > (zipper_length + MXC_ERROR_LENGTH))MXC_SetAlarmCode(MXC_NO_SEBIAO_ALARM);
                        }
                        
                        if(!X_DRV)
                        {
                            if(dwZipCnt!=0)
                            {
                                if((save_buff - dwRealPos) < (zipper_length - MXC_ERROR_LENGTH))MXC_SetAlarmCode(MXC_NO_SEBIAO_ALARM);
                            }
                            MXC_cMotorStep = 0;
                        }
                        else if(dwTickCount >= MXC_cMotorDelay)MXC_SetAlarmCode(MXC_NO_SEBIAO_ALARM);
                        break;	
	}
}
//下冲
void  MXC_NiLongXiuCiJi_XiaC(void)
{       
    switch(MXC_cXiaChongStep)
    { 
    case 0:
            return;
            break;
    case 1:
            {
                MXC_cRightFenZhenStep = 1;	
                MXC_cLeftFenZhenStep  = 0;
                cRFengTimer = 0;
                cLFengTimer = 0;
            }
            MXC_cXiaChongStep = 2;
            break;
    case 2:
            if((MXC_cRightFenZhenStep==0) && (MXC_cLeftFenZhenStep==0))
            {
                  if(MXC_XiaChongMotorMode)
                      MXC_XC_SongZhou = MXC_SERVER_DISEN;  
                  else
                      MXC_XC_ShaChe   = MXC_SC_DISEN;
                      MXC_XC_SongZhou = MXC_SERVER_EN; //刹车打开

                  if(MXC_bRunning)MXC_cXiaChongDelay = dwTickCount + MXC_PARAM_DELAY_XC;
                  MXC_cXiaChongStep = 3;
            }
            break;
    case 3:
            if(dwTickCount >= MXC_cXiaChongDelay)
            {
                    MXC_cXiaChongStep = 4;	
                    MXC_XiaChong_MOTOR = 1;  //下冲电机  
                    MXC_cXiaChongDelay = dwTickCount + (unsigned long)ERRORTIME;   //下冲最长时间   	

                    if(MXC_XiaChongMotorMode == 1)
                    {
                            AxisMoveTwoPos(Y_AXIS,MXC_XiaChongSpeed,2000,MXC_XiaChongLowSpeed,9999999,0);
                    }	
    }
    break;
    case 4:  //碰到右大微动,延时停
            if(MXC_XiaChong_IN_UP)
            {
                  MXC_cXiaChongDelay = dwTickCount + MXC_PARAM_XC_DELAY;
                  MXC_cXiaChongStep = 5;
                  MXC_LeftFenZhen_VAVLE = 0;  	//退左分针
                  MXC_RightFenZhen_VAVLE = 0;	//退右分针	
                  MXC_GouZhen_VAVLE = 1;
                  MXC_cGouZhenTime  = dwTickCount + 300;
            }
            else if(dwTickCount >= MXC_cXiaChongDelay) //自动停机
            {	
                  MXC_cXiaChongStep = 0;
//                  MXC_ShaChe_Output();////刹车
                  MXC_XiaChong_MOTOR = 0;// 	//下冲电机
                  MXC_SetAlarmCode(MXC_XC_ALARM);
                  MXC_LeftFenZhen_VAVLE = 0;   	//退左分针
                  MXC_RightFenZhen_VAVLE = 0;	//退右分针
                  AxisEgmStop(Y_AXIS);
            }
            
            break;
    case 5:	
            if(dwTickCount >= MXC_cXiaChongDelay)	
            {
                    
                    AxisEgmStop(Y_AXIS);
                    MXC_XiaChong_MOTOR = 0;      //延时刹车
                    if(MXC_PARAM_SC_MODE)
                    {
                        MXC_cXiaChongStep = 0;
                    }
                    else
                    {
                        MXC_cXiaChongStep = 6;
                    }
                    
 //                   MXC_cXiaChongDelay = dwTickCount + MXC_PARAM_SC_DELAY;			
            }
            break;
    case 6:	
           // if((dwTickCount >= MXC_cXiaChongDelay))
            {
                    MXC_cXiaChongStep = 7;
                    MXC_cXiaChongDelay = dwTickCount + MXC_PARAM_SC_DELAY;	
                   // MXC_ShaChe_Output();	
            }
            break;
    case 7:
            if((dwTickCount >= MXC_cXiaChongDelay))
            {
                    MXC_cXiaChongStep = 0;
                    MXC_cXiaChongDelay = dwTickCount;
                    MXC_XC_SongZhou = MXC_SERVER_DISEN;  
            }	
            break;
    case 20:                      // 点动普通下冲动作
                MXC_XC_SongZhou = MXC_SERVER_EN;
                MXC_cXiaChongDelay = dwTickCount + 50;	
                MXC_cXiaChongStep = 21;
            break;
    case 21:   
               if((dwTickCount >= MXC_cXiaChongDelay))
               {
                    MXC_XiaChong_MOTOR = 1;
                    MXC_cXiaChongDelay = dwTickCount + 50;	
                    MXC_cXiaChongStep = 22;
               }
            break;
    case 22:   
               if((dwTickCount >= MXC_cXiaChongDelay))
               {
                    MXC_XiaChong_MOTOR = 0;
                    MXC_XC_SongZhou    = MXC_SERVER_EN;
                    
                    if(MXC_XiaChongMotorMode)
                        MXC_cXiaChongStep = 0;
                    else
                    {
                        MXC_cXiaChongDelay = dwTickCount + 150;	
                        MXC_cXiaChongStep = 23;
                    }
               }
            break;
    case 23:   
               if((dwTickCount >= MXC_cXiaChongDelay))
               {
                    MXC_XC_SongZhou    = MXC_SERVER_DISEN;                                                               
                    MXC_cXiaChongStep  = 0;
               }
            break;
    case 40:                      // 点动电机下冲动作
                MXC_XC_SongZhou = MXC_SERVER_EN;
                MXC_cXiaChongDelay = dwTickCount + 50;	
                MXC_cXiaChongStep = 41;
            break;
    case 41:   
                if(!Y_DRV)AxisMovePos(Y_AXIS,20,10);
                MXC_cXiaChongStep = 42;
            break;
    case 42:   
           if(!Y_DRV)
           { 
                MXC_cXiaChongStep = 0;
           }
            break;
    }
}

 //分针
void  MXC_NiLongXiuCiJi_FenZhengProc(void)
{
	if(MXC_FenZSelect==0)
	{
            MXC_cLeftFenZhenStep = 0;
            MXC_cRightFenZhenStep = 0;	
	}	
	//右分针
	switch(MXC_cRightFenZhenStep)
	{ 
            case 0:
                    break;
            case 1:
                        MXC_cFenZhenRightDelay = MXC_PARAM_R_FZ_DELAY+dwTickCount;
                        MXC_cRightFenZhenStep  = 2;
                    break;
            case 2:
                    if(dwTickCount >= MXC_cFenZhenRightDelay)
                    {
                        MXC_cRightFenZhenStep = 3;
                        MXC_RightFenZhen_VAVLE = 1;//右分针电磁阀
                        MXC_cFenZhenRightDelay = dwTickCount + FenZhengErrorTime;      	
                    }	
            break;
            case 3:  //碰到右大微动,延时停
                    if(!MXC_RightFenZhen_Origin_IN)   //右分针原点离开
                    {
                        MXC_cFenZhenRightDelay = dwTickCount + FenZhengErrorTime;
                        MXC_cRightFenZhenStep = 4;
                    }//右分针不下去
                    else if(dwTickCount >= MXC_cFenZhenRightDelay)
                    {
                         MXC_SetAlarmCode(MXC_FEN_ZHEN_ALARM);			
                    }
                    break;
            case 4:	
                    if(MXC_RighttFenZhen_IN)  //插针到位
                    {
                        MXC_cRightFenZhenStep = 0;
                        MXC_cLeftFenZhenStep = 1;   //左分针延时启动
                    }
                    else if(dwTickCount >= MXC_cFenZhenRightDelay)
                    {
                            MXC_RightFenZhen_VAVLE = 0;//右分针
                            cRFengTimer++; 
                            //当右分针分不到位时，左分针也要重新分针
                            MXC_LeftFenZhen_VAVLE = 0;
                            MXC_cRightFenZhenStep = 0;
                            if(cRFengTimer < 4)
                            {
                                MXC_cRightFenZhenStep = 5;
                                MXC_cFenZhenRightDelay = dwTickCount + FenZhengErrorTime;
                            }
                            else
                            {
                                MXC_SetAlarmCode(MXC_FEN_ZHEN_ALARM);		
                            }
                    }
                    break;
            case 5:	
                    if(MXC_RightFenZhen_Origin_IN)  //退到位
                    {
                        MXC_cRightFenZhenStep = 6;
                    }
                    else if(dwTickCount >= MXC_cFenZhenRightDelay)
                    {
                         MXC_SetAlarmCode(MXC_FEN_ZHEN_ALARM);	
                    }
                    break;
            case 6:
                    {
                         MXC_cRightFenZhenStep = 1;
                    }	
                    break;
	}
	//左分针
	switch(MXC_cLeftFenZhenStep)
	{ 
		case 0:
			break;
                case 1:
                        MXC_cFenZhenLeftDelay = MXC_PARAM_L_FZ_DELAY+dwTickCount;
                        MXC_cLeftFenZhenStep = 2;
                        break;
		case 2:
			if(dwTickCount >= MXC_cFenZhenLeftDelay)
			{
                            MXC_cLeftFenZhenStep = 3;
                            MXC_LeftFenZhen_VAVLE = 1; //左分针电磁阀
                            MXC_cFenZhenLeftDelay = dwTickCount + FenZhengErrorTime;      	
 			}	
        	break;
		case 3:  //离开左分针原点
			if(!MXC_LeftFenZhen_Origin_IN)   //左分针原点离开
			{
                            MXC_cFenZhenLeftDelay = dwTickCount + FenZhengErrorTime;
                            MXC_cLeftFenZhenStep = 4;
			}//左分针不下去
			else if(dwTickCount >= MXC_cFenZhenLeftDelay)
			{
			    MXC_SetAlarmCode(MXC_FEN_ZHEN_ALARM);					
			}
			break;
		case 4:	
			if(MXC_LeftFenZhen_IN)  //插针到位
				MXC_cLeftFenZhenStep = 0;
			else if(dwTickCount >= MXC_cFenZhenLeftDelay)
			{
                            MXC_LeftFenZhen_VAVLE = 0;//左分针
                            cLFengTimer++; 
                            if(cLFengTimer < 6)
                            {
                                  MXC_cLeftFenZhenStep = 5;
                                  MXC_cFenZhenLeftDelay = dwTickCount + FenZhengErrorTime;
                                  if((cLFengTimer%2) == 0)
                                  {
                                      MXC_RightFenZhen_VAVLE = 0;
                                      MXC_cRightFenZhenStep = 0;
                                  }
                            }
                            else
                            {					
                                  MXC_SetAlarmCode(MXC_FEN_ZHEN_ALARM);	
                            }
			}
			break;
		case 5:	
			if(MXC_LeftFenZhen_Origin_IN)  //退到位
			{
                            MXC_cLeftFenZhenStep = 6;
			}
			else if(dwTickCount >= MXC_cFenZhenLeftDelay)
			{
                            MXC_SetAlarmCode(MXC_FEN_ZHEN_ALARM);						
			}
			break;
		case 6:
                        if((cLFengTimer%2) == 0)  //左边插两次都插不到，就退右边再同时插
                        {
                              MXC_cRightFenZhenStep = 1;
                              cRFengTimer = 0;
                              MXC_cLeftFenZhenStep = 0;
                        }
                        else
                        {
                             MXC_cLeftFenZhenStep = 1;
                        }	
			break;
	}
}



#endif