GC23005/Machine/XiDongMachine/XDJiaoYaDinCun.h

#ifndef __XDJIAOYADINCUN_H__
#define __XDJIAOYADINCUN_H__

#if XI_DONG_MACHINE

extern void JYDC_InitAction(void);
extern void JYDC_ManualAction(void);
extern void JYDC_Action(void);
extern void JYDC_DelayAction(void);
extern void JYDC_ExtiActionX30(void);
extern void JYDC_ExtiActionX31(void);
//0
typedef struct
{
    unsigned long Total;       //0生产总量
    unsigned long SetTotal;    //2产量设置
    unsigned long CurLength;   //4
    unsigned long SetLength;   //6拉链长度
    unsigned long CurLength_JY;//8当前位置
    unsigned short CntDir;     //10
    unsigned short SetSpeed;   //11胶牙定寸速度
    unsigned short SetAccDec;  //12
    unsigned short ShaCheDelayTime;//13延时刹车
    unsigned short ShaCheTime; //14刹车持续时间
    unsigned short DelayChuiQiTime;//15
    unsigned short XC_AlarmTime;//16下冲报警时间
    unsigned short XC_DelayTime;//17延时下冲
    unsigned short SetDaoKouLength;//18
    unsigned short res2;           //19
    unsigned short EncCircleLength;//20
    unsigned short SetSlowLength;  //21
    unsigned short SetKouWeiLength;//22  
    unsigned short JiZhunChiShu;//23
    unsigned short JiZhunLength;//24
    unsigned short LowSpeed;    //25慢速度
    unsigned short ReviseChi;   //26修正齿数
    unsigned short KongWeiLength;//27除齿长度
    unsigned short DaoKouLength; //28刀口长度
    unsigned short SetSlow;       //29慢速长度
    unsigned short SetChuiQiTime;  //30吹气持续时间
    unsigned short XiChiEn;      //31铣齿电机开关
    unsigned short MotorCyclePulse;//32电机细分
    unsigned short MotorCycleLength;//33拖带轮周长
    unsigned short MotorAccTime;    //34电机加速时间
    unsigned short MotorDecTime;    //35电机减速时间
    unsigned short res4[15];     //36~50
    unsigned short ModeSelect;    //51当前模具类型选择
    unsigned short JiZhunChiShu_1;//52 3号模具齿数
    unsigned short JiZhunLength_1;//53 3号模具长度
    unsigned short SetDaoKou_1;   //54 3号模具刀口长度
    
    unsigned short JiZhunChiShu_2;//55 5号模具齿数
    unsigned short JiZhunLength_2;//56 5号模具长度
    unsigned short SetDaoKou_2;   //57 5号模具刀口长度
    
    unsigned short JiZhunChiShu_3;//58 8号模具齿数
    unsigned short JiZhunLength_3;//59 8号模具长度
    unsigned short SetDaoKou_3;   //60 8号模具刀口长度
    
    unsigned short JiZhunChiShu_4;//61 特殊模具齿数
    unsigned short JiZhunLength_4;//62 特殊模具长度
    unsigned short SetDaoKou_4;   //63 特殊模具刀口长度
    unsigned short res5[10];      //64~73
    unsigned short PassWordError;    //74
    unsigned short res6[46];         //75~120
    unsigned short DisplayData[8];   //121
    unsigned short res7[232];
    unsigned short NowGroup;         //361
    unsigned long  AllSetLength;     //362
    unsigned long  AllSetTotal;      //364
    unsigned long  AllOverZipLength; //366
    unsigned long  AllOverZipTotal;  //368
    unsigned short res8[32];
    unsigned long  ZipperLength[5];//400~409
    unsigned short  KongWeiTooth[5];//410~414
    unsigned short ReviseTooth[5];//415~419
    unsigned long  SetZipTotal[5];   //420~429
    unsigned long  OverZipTotal[5];//430~439
    unsigned long  ZipperLengthBuff;//440
    unsigned short KongWeiToothBuff;//442
    unsigned short ReviseToothBuff; //443
    unsigned long  SetZipTotalBuff; //444
    unsigned long  OverZipTotalBuff;//446
} JYDC_ParamStrct;

#define	SET_LEN_ADDR	     6
#define	SET_LEN_ADDR_JY	     26
#define CLR_PULSE_DELAY      100
#define MAXSPEED	     150
#define JYDC_ALARM_ADDR      100
#define JYDC_TOTAL_ADDR      0
#define JYDC_PROSPEED_ADDR   78


//故障代码列表
#define JYDC_NO_ALARM         0
#define JYDC_TOTAL_ALARM      1
#define JYDC_KADAI_ALARM      2
#define JYDC_XIACHONG_ARRIVE_ALARM 3
#define JYDC_COUNT_ALARM      4
#define JYDC_START_XIACHONG_ALARM  5
#define JYDC_SEBIAO_ALARM          6


#define NO_TOOTHCOUT_TIME    user_datas[81]  //多久没感应到数齿信号异常

#define	SET_ACCDEC	     10

#define JYDC_XiaChongStep cStepMByte3
#define JYDC_ManualStep cStepMByte2
#define JYDC_MotorStep cStepMByte1
#define JYDC_AutoStep  cStepMByte
#define JYDC_cChuiQiStep cStepMByte4

#define JYDC_XiaChongDelay cDelayTime1
#define JYDC_AutoDelay     cDelayTime2
#define JYDC_ChuiQiDelay   cDelayTime3
#define JYDC_XiChiChuiQiDelay   cDelayTime4

#define SET_ZIPPER_LENGTH  (user_datas[6] |  user_datas[7] << 16) 
#define SET_TOTAL          (user_datas[2] |  user_datas[3] << 16) 
#define JYDC_PARAM_REVICHISHU      user_datas[26]
#define JYDC_PARAM_CHUIQI_TIME     (user_datas[30]*10)
#define	CUR_LEN_JY	           user_datas[8]
#define JYDC_PARAM_DELAY_CHUIQI_TIME (user_datas[10]*10)
#define JYDC_PARAM_SET_SPEED       user_datas[11]
#define JYDC_PARAM_LOW_SPEED       user_datas[25]
#define	SET_KOUWEI_JY	           user_datas[27]    //除齿长度
#define JYDC_PARAM_LOW_LENGTH      user_datas[29]
#define	JYDC_PARAM_XC_ALARM_TIME  user_datas[16]//JYDC_Param->XC_AlarmTime	//下冲最长时间
#define	JYDC_PARAM_SHACHE_DELAY_TIME	user_datas[13]//JYDC_Param->ShaCheDelayTime	//下冲最长时间
#define	JYDC_PARAM_SHACHE_TIME		100   //JYDC_Param->ShaCheTime	        //刹车时间
#define	CUIQI_TIME		user_datas[30]//JYDC_Param->CuiQiTime	        //吹气时间
#define	XIACONG_DELAY_TIME	user_datas[17]//JYDC_Param->XC_DelayTime	//下冲最长时间

#define SET_ZIPPER_LENGTH_INCH  (user_datas[31] |  user_datas[32] << 16) 
#define JYDC_PARAM_CYCLE_DELAY  user_datas[33]
//user_datas[34]                数齿信号方向
#define JYDC_SEBIAO_MODE        user_datas[35]//色标模式，0为普通1为色标模式
#define JYDC_SEBIAO_DELAY       user_datas[36]//色标模式延迟下冲齿数
#define JYDC_XICHI_MOTOR_MODE   user_datas[37]//0为自动的时候不用铣齿电机，1为使用

#define DISPLAY_DATA0           user_datas[121]
#define DISPLAY_DATA1           user_datas[122]
#define DISPLAY_DATA2           user_datas[123]
#define DISPLAY_DATA3           user_datas[124]
#define DISPLAY_DATA4           user_datas[125]
#define DISPLAY_DATA5           user_datas[126]
#define DISPLAY_DATA6           user_datas[127]
#define DISPLAY_DATA7           user_datas[128]

#define MODE_SELECT             user_datas[51] 
#define	JY_JIZHUN_CISHU		user_datas[23]     //基准齿数
#define	JY_JIZHUN_LEN		user_datas[24]     //基准长度
#define	SET_DAOKOU_JY	        user_datas[28]     //机械模具刀口
                                                   //3#
#define	JY_JIZHUN_CISHU1	user_datas[52]     //基准齿数
#define	JY_JIZHUN_LEN1		user_datas[53]     //基准长度
#define	SET_DAOKOU_JY1	        user_datas[54]     //机械模具刀口
                                                   //5#
#define	JY_JIZHUN_CISHU2	user_datas[55]     //基准齿数
#define	JY_JIZHUN_LEN2		user_datas[56]     //基准长度
#define	SET_DAOKOU_JY2	        user_datas[57]     //机械模具刀口
                                                   //8#
#define	JY_JIZHUN_CISHU3	user_datas[58]     //基准齿数
#define	JY_JIZHUN_LEN3		user_datas[59]     //基准长度
#define	SET_DAOKOU_JY3	        user_datas[60]     //机械模具刀口
                                                   //特殊刀模
#define	JY_JIZHUN_CISHU4	user_datas[61]     //基准齿数
#define	JY_JIZHUN_LEN4		user_datas[62]     //基准长度
#define	SET_DAOKOU_JY4	        user_datas[63]     //机械模具刀口


#define START_IN     X00
#define START_IN_UP (X00 && !OLDX00)
#define STOP_IN      X01
#define STOP_IN_UP  (X01 && !OLDX01)
#define JYDC_ManXiaChong_UP (X02 && !OLDX02)
#define JYDC_ChuDai_IN_UP   (X12 && !OLDX12)
#define JYDC_ChuDai_IN_DW   (!X12 && OLDX12)
#define JYDC_ChuDai_IN      (X12)

#define JYDC_XiaChong_IN    X14
#define JYDC_XiaChong_IN_UP (X14 && !OLDX14)

#define JYDC_XiaChong_IN_DW   (!X14 && OLDX14)

#define JYDC_KaDai_IN       X03

#define JYDC_COUNT_IN_UP   (X16 && !OLDX16)
#define JYDC_COUNT_IN_DW   (!X16 && OLDX16)

#define JYDC_ShaChe_VAVLE   Y00
#define JYDC_ChuiQi_VAVLE   Y01
#define JYDC_SuoChi_VAVLE   Y02
#define JYDC_XiaChong_MOTOR Y04
#define JYDC_XiChiChuiQi_VAVLE Y13
#define JYDC_XiChi_MOTOR    Y14

#define ALARM_LED           Y04

//M0~M4 Actioon.h全局使用


#define JYDC_bManSuoChi     M0005
#define JYDC_bTest          M0006
#define JYDC_bManChuiQi     M0007
#define JYDC_bManXiaChong   M0008
#define JYDC_bStart         M0009
#define JYDC_bAddTooth      M0010
#define JYDC_bDecTooth      M0011
#define JYDC_bChangeLength  M0016
#define JYDC_bRunning       M0017
#define JYDC_bStop          M0018
#define JYDC_bSingleOrGroup M0019
#define JYDC_bManXiChiMotor M0020
#define JYDC_bAlarmStop    M0036
#define JYDC_bSetInch      M0039
#define JYDC_bSetTooth     M0040
#define JYDC_bManMotor     M0041

#endif

#endif