GC23005/Machine/XiDongMachine/XDYYaJi.c

#include "global.h"


#if XI_DONG_MACHINE


void YYa_AlarmProtect(void);
void YYa_ManualAction(void);
void YYa_AutoAction(void);
void YYa_StepCheckStart(void);
void YYa_ExtiActionX31(void);
void YYa_SongLiao(void);
void YY_JieTouControl(void);
void YY_ZhuYou(void);
void YY_Stop_Action(void);
void YY_StartZYFirst(void);

float YY_CalToothLength(unsigned short roll_diameter,unsigned short tooth_num);
//输入齿数计算长度返回的是单位厘米
unsigned long YY_ToothNumCalLengthCM(float single_length,unsigned short tooth_num,unsigned long zipper_num);
//输入齿数计算长度返回的是单位英寸
unsigned long YY_ToothNumCalLengthInch(float single_length,unsigned short tooth_num,unsigned long zipper_num);
//输入长度厘米算齿数
unsigned long YY_ToothLengthCMCalNum(float single_length,unsigned short tooth_length,unsigned long zipper_num);
//输入长度厘米算英寸
unsigned long YY_ToothLengthCMCalInch(float single_length,unsigned short tooth_length,unsigned long zipper_num);
//输入厘米长度计算总长度单位米
unsigned long YY_LengthCalLengthM(unsigned short set_length,unsigned short kongwei_length,unsigned long zipper_num);
//输入英寸长度计算总长度
unsigned long YY_InchLengthCalLength(unsigned short set_length,unsigned short kongwei_length,unsigned long zipper_num);
//输入齿数计算长度返回的是单位米
unsigned long YY_ToothNumCalLength(float single_length,unsigned short tooth_num,unsigned long zipper_num);
//输入齿数计算长度返回的是单位米带浮点型
float YY_ToothNumCalLengthFloat(float single_length,unsigned short tooth_num,unsigned long zipper_num);
//输入长度英寸算齿数
unsigned long YY_ToothLengthInchCalNum(float single_length,unsigned short tooth_length,unsigned long zipper_num);
//输入长度英寸算厘米
unsigned long YY_ToothLengthInchCalCM(float single_length,unsigned short tooth_length,unsigned long zipper_num);

void YY_SetLeftPyData(unsigned short cLeftData,unsigned short cLeftKongWei);
void YY_SetRightPyData(unsigned short cRightData,unsigned short cRightKongWei);
void SetLeftSpaceDisplay(unsigned char mode,unsigned short source_data);
void SetRightSpaceDisplay(unsigned char mode,unsigned short source_data);

void YY_SetLeftDCTSpace(void);
void YY_SetRightDCTSpace(void);
void YY_SetLeftDCTTooth(void);
void YY_SetRightDCTTooth(void);

unsigned long YY_GetLeftToothNum(void);
unsigned long YY_GetRightToothNum(void);
unsigned long YY_GetLeftToothNumDisplay(void);
unsigned long YY_GetRightToothNumDisplay(void);

unsigned long YY_GetLeftSpace(void);
unsigned long YY_GetRightSpace(void);
unsigned long YY_GetLeftSpaceDisplay(void);
unsigned long YY_GetRightSpaceDisplay(void);

void YY_SetLeftDisplay(unsigned short source_data);
void YY_SetRightDisplay(unsigned short source_data);
void YY_SetLeftSpaceDisplay(unsigned short source_data);
void YY_SetRightSpaceDisplay(unsigned short source_data);

void YY_AddTotal(void);
unsigned long YY_GetTotal(void);
unsigned long YY_GetSetTotal(void);

void YY_LeftToothDisplayAdd(void);
void YY_RightToothDisplayAdd(void);
void YY_LeftSpaceDisplayAdd(void);
void YY_RightSpaceDisplayAdd(void);

void YY_LeftOverSet(void);
void YY_RightOverSet(void);

float YY_SingleToothLength;
unsigned long YY_cTotal,YY_ProOnceTime,YY_cJieDaiClrTotal,YY_cJieDaiState,YY_cJieDaiTotal;
unsigned char YY_RightCountEnable,YY_cOverTotalLeftFlg = 0,YY_cOverTotalRightFlg = 0,YY_LeftOk,YY_RightOk,YY_ChangeNextGroupFlg,YY_cTatal_OK,YY_CalUseLifeFlg,
                YY_SaveParamFlg,YY_UseLifeNowGroup,YY_LastGroup,YY_cHeLian,YY_bOldMode,YY_OldGroup;
unsigned short YY_NowLeftPyNum,YY_NowRightPyNum,YY_NowLeftPyKongWei,YY_NowRightPyKongWei,YY_ZYBuff,YY_cStartWorkTime;
unsigned short YY_cStartPYFlag_Left,YY_cStartPYFlag_Right;

YY_SingleParam_str *YY_SingleParam;
YY_GroupParam_str *YY_GroupParam;
YY_SystemParam_str *YY_SystemParam;
YY_ComponentParam_str *YY_ComponentParam;



void YYa_SetAlarmCode(unsigned short alarm_code)
{
    YY_SystemParam->AlarmCode |= alarm_code;
    YY_bAlarmStop = 1;
}

void YYa_SetLifeAlarmCode(unsigned short alarm_code)
{
    YY_ComponentParam->LifeAlarm |= 0x0001 << alarm_code;
}

void YYa_InitAction(void)
{ 
   static unsigned long start_delay;
   
   YY_SingleParam = (YY_SingleParam_str *)&user_datas[YY_SINGLE_ADDR];
   YY_GroupParam =  (YY_GroupParam_str *)&user_datas[YY_GROUP_ADDR];
   YY_SystemParam = (YY_SystemParam_str *)&user_datas[YY_SYSTEM_ADDR];
   YY_ComponentParam = (YY_ComponentParam_str *)&user_datas[YY_LIFE_ADDR];
   
   if(YY_SystemParam->NowGroup > 4)YY_SystemParam->NowGroup = 0;
    
    YY_SingleToothLength     = YY_CalToothLength(YY_SystemParam->ToothLength,YY_SystemParam->ToothNum);   
    YY_bMode   = YY_SINGLE_MODE;
    YY_bDCTEnable  = 1;
    YY_cTotal = YY_GetTotal();
    
    YY_StartZYFirst();
    YY_bCalculateTotal = 1;   //bCalculate
    YY_SystemParam->AlarmCode = 0;
    start_delay = dwTickCount + 1000;
    while(dwTickCount <= start_delay)
    {
       io_app_read_input();
    }
}

void YYa_Action(void)
{
    YYa_ManualAction();
    YYa_AutoAction();
    YY_ZhuYou();
    YYa_SongLiao();
    YYa_StepCheckStart();   // 调用脚踏开关检测程序
    YYa_AlarmProtect();
}

void YY_ClearJTData(void)
{
      YY_cJieDaiState = 0;
      YY_cJieDaiTotal = 0;
      YY_cJieDaiClrTotal = 0;
}

//重设数据
void YY_ReSetData(void)
{   
    unsigned char i;
    switch(YY_bMode)
    {
        case YY_SINGLE_MODE:
        {   
            if((YY_SingleParam->DisplyLeftToothNum != YY_SingleParam->DisplyRightToothNum) || (YY_SingleParam->DisplyLeftToothNumSpace != YY_SingleParam->DisplyRightToothNumSpace))
                YY_RightCountEnable = 1;
            else
                YY_RightCountEnable = 0;
            YY_SingleParam->DisplyLeftToothNum    = 0;
            YY_SingleParam->DisplyLeftToothLengthCM = 0; 
            YY_SingleParam->DisplyLeftToothLengthINCH = 0; 
            YY_SingleParam->DisplyLeftToothNumSpace     = 0; 
            YY_SingleParam->DisplyLeftToothLengthCMSpace = 0; 
            YY_SingleParam->DisplyLeftToothLengthINCHSpace = 0; 
            YY_SingleParam->DisplyRightToothNum = 0;       
            YY_SingleParam->DisplyRightToothLengthCM = 0; 
            YY_SingleParam->DisplyRightToothLengthINCH = 0; 
            YY_SingleParam->DisplyRightToothNumSpace = 0;      
            YY_SingleParam->DisplyRightToothLengthCMSpace = 0;  
            YY_SingleParam->DisplyRightToothLengthINCHSpace = 0; 
            YY_ClearJTData();
 
        }break;
        case YY_GROUP_MODE:
        {
            if((YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup] != YY_GroupParam->DisplyRightToothNum[YY_SystemParam->NowGroup]) || (YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup] != YY_GroupParam->DisplyRightToothNumSpace[YY_SystemParam->NowGroup]))
            {
                YY_RightCountEnable = 1;
            }
            else
            {
                YY_RightCountEnable = 0;
            }
            
            for(i = 0;i < 5;i++)
            {
                YY_GroupParam->DisplyLeftToothNum[i]    = 0;
                YY_GroupParam->DisplyLeftToothLengthCM[i] = 0;
                YY_GroupParam->DisplyLeftToothLengthINCH[i]     = 0;
                YY_GroupParam->DisplyLeftToothNumSpace[i]= 0;
                YY_GroupParam->DisplyLeftToothLengthCMSpace[i]= 0;
                YY_GroupParam->DisplyLeftToothLengthINCHSpace[i]= 0;
                YY_GroupParam->DisplyRightToothNum[i]= 0;
                YY_GroupParam->DisplyRightToothLengthCM[i]= 0;
                YY_GroupParam->DisplyRightToothLengthINCH[i]= 0;
                YY_GroupParam->DisplyRightToothLengthCM[i]= 0;
                YY_GroupParam->DisplyRightToothLengthCMSpace[i]= 0;
                YY_GroupParam->DisplyRightToothLengthINCHSpace[i]= 0;
                YY_ClearJTData();
            }
        }break;        
    }
}

unsigned long YY_CalOverLength(void)
{
    unsigned char i;
    switch(YY_bMode)
    {
       case YY_SINGLE_MODE:
       {
           YY_SingleParam->OverLength = (YY_SingleParam->LeftToothLengthCM + YY_SingleParam->LeftToothLengthCMSpace) * YY_SingleParam->OverTotal / 1000;
       }break;
       case YY_GROUP_MODE:
       {
           YY_GroupParam->AllOverLength = 0;
           for(i=0;i<5;i++)
           {
               YY_GroupParam->AllOverLength += (YY_GroupParam->LeftToothLengthCM[i] + YY_GroupParam->LeftToothLengthCMSpace[i]) * YY_GroupParam->OverSetTotal[i] / 1000;
           }
       }break;
       default:return 0;
    }
    return 0;
}

void YY_CalProcessTime(unsigned long add_time)
{
    unsigned long time_buff,hour_buff,minute_buff;
    unsigned char i;

    switch(YY_bMode)
    {
        case YY_SINGLE_MODE:
        {
              if(YY_MAIN_MOTOR)
              {

                  time_buff  = YY_SingleParam->OverTotal * (YY_SingleParam->LeftToothNum + YY_SingleParam->LeftToothNumSpace) * add_time;

                  time_buff  = time_buff / 1000;
                  
                  hour_buff = time_buff / 3600;
                          
                  YY_SingleParam->SetTimeHour  = hour_buff;    
                  time_buff -= hour_buff * 3600;
                        
                  minute_buff = time_buff / 60;
                  
                  YY_SingleParam->SetTimeMinute = minute_buff;    
              }
        }break;
        case YY_GROUP_MODE:
        {          
              if(YY_MAIN_MOTOR)
              { 
                  time_buff = 0;
                  for(i=0;i<5;i++)
                  {
                      time_buff += YY_GroupParam->OverSetTotal[i] * (YY_GroupParam->LeftToothNum[i] + YY_GroupParam->LeftToothNumSpace[i]) * add_time;
                  }

                  time_buff  = time_buff / 1000;
                  
                  hour_buff = time_buff / 3600;
                          
                  YY_GroupParam->SetTimeHour  = hour_buff;    
                  time_buff -= hour_buff * 3600;
                        
                  minute_buff = time_buff / 60;
                  
                  YY_GroupParam->SetTimeMinute = minute_buff;    
                                     
              }
        }break;
    }
}

void YY_CalRemainTime(unsigned long one_time)
{
    unsigned long  time_buff,hour_buff,minute_buff;
    unsigned char i;
    
    switch(YY_bMode)
    {
        case YY_SINGLE_MODE:
        {
              time_buff = one_time *  (YY_SingleParam->SetTotal - YY_SingleParam->OverTotal) * (YY_SingleParam->LeftToothNum + YY_SingleParam->LeftToothNumSpace);
              
              time_buff  = time_buff / 1000;
              
              hour_buff = time_buff / 3600;
                      
              YY_SingleParam->RemainTimeHour  = hour_buff;    
              time_buff -= hour_buff * 3600;
                    
              minute_buff = time_buff / 60;
              
              YY_SingleParam->RemainTimeMinute = minute_buff;    
                                
        }break;
        case YY_GROUP_MODE:
        {          
              time_buff = 0;
              for(i=0;i<5;i++)
              {
                  time_buff += (YY_GroupParam->SetTotal[i] - YY_GroupParam->OverSetTotal[i]) * (YY_GroupParam->LeftToothNum[i] + YY_GroupParam->LeftToothNumSpace[i]) * one_time;
              }
              time_buff  = time_buff / 1000;
              
              hour_buff = time_buff / 3600;
                      
              YY_GroupParam->RemainTimeHour  = hour_buff;    
              time_buff -= hour_buff * 3600;
                    
              minute_buff = time_buff / 60;
              
              YY_GroupParam->RemainTimeMinute = minute_buff;    
        }break;
    }
}
void YY_cTotal_Time(void)
{
    YY_CalOverLength();
    YY_CalProcessTime(YY_ProOnceTime);
    YY_CalRemainTime(YY_ProOnceTime);
}
//参数运算控制
void YY_CalculataParam(void)
{
    unsigned char i;
    unsigned long total_buff;
    
    if(YY_bMode != YY_bOldMode)
    {
        YY_cTotal = YY_GetTotal();
    }
    YY_bOldMode = YY_bMode;
    
    if(YY_SystemParam->NowGroup != YY_OldGroup)
    {
        YY_SystemParam->NextGroupBuff = YY_SystemParam->NowGroup + 1;
    }
    YY_OldGroup  = YY_SystemParam->NowGroup;
    
//输入右边的齿数    
    if(YY_bCalInputRightToothNum)
    {
        YY_bCalInputRightToothNum = 0;
        
        YY_SingleParam->RightToothNumSpace = (YY_SingleParam->LeftToothNumSpace + YY_SingleParam->LeftToothNum) - YY_SingleParam->RightToothNum;
        YY_bCalInputToothNum      = 1;
    }
    
    if(YY_bCalInputRightKongWei)
    {
        YY_bCalInputRightKongWei = 0;
        
        YY_SingleParam->RightToothNum = (YY_SingleParam->LeftToothNumSpace + YY_SingleParam->LeftToothNum) - YY_SingleParam->RightToothNumSpace;
        YY_bCalInputToothNum      = 1;
    }
//输入右边的长度     
    if(YY_bCalInputRightToothNumLength)
    {
        YY_bCalInputRightToothNumLength = 0;
        
        YY_SingleParam->RightToothLengthCMSpace = (YY_SingleParam->LeftToothLengthCMSpace + YY_SingleParam->LeftToothLengthCM) - YY_SingleParam->RightToothLengthCM;
        YY_bCalInputLength      = 1;
    }
    
    if(YY_bCalInputRightKongWeiLength)
    {
        YY_bCalInputRightKongWeiLength = 0;
        
        YY_SingleParam->RightToothLengthCM = (YY_SingleParam->LeftToothLengthCMSpace + YY_SingleParam->LeftToothLengthCM) - YY_SingleParam->RightToothLengthCMSpace;
        YY_bCalInputLength      = 1;
    }
//输入右边的英寸长度     
    if(YY_bCalInputRightToothNumLengthInch)
    {
        YY_bCalInputRightToothNumLengthInch = 0;
        
        YY_SingleParam->RightToothLengthINCHSpace = (YY_SingleParam->LeftToothLengthINCHSpace + YY_SingleParam->LeftToothLengthINCH) - YY_SingleParam->RightToothLengthINCH;
        YY_bCalInputLengthInch      = 1;
    }
    
    if(YY_bCalInputRightKongWeiLengthInch)
    {
        YY_bCalInputRightKongWeiLengthInch = 0;
        
        YY_SingleParam->RightToothLengthINCH = (YY_SingleParam->LeftToothLengthINCHSpace + YY_SingleParam->LeftToothLengthINCH) - YY_SingleParam->RightToothLengthINCHSpace;
        YY_bCalInputLengthInch      = 1;
    }
    
    
    if(YY_bCalInputToothNum)
    {
        YY_bCalInputToothNum = 0;        
        
        YY_SingleParam->LeftToothLengthCM = YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_SingleParam->LeftToothNum,1);
        YY_SingleParam->LeftToothLengthINCH =  YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_SingleParam->LeftToothNum,1);
        
        YY_SingleParam->RightToothLengthCM =  YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_SingleParam->RightToothNum,1);       
        YY_SingleParam->RightToothLengthINCH =  YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_SingleParam->RightToothNum,1);
        
        YY_SingleParam->LeftToothLengthCMSpace =  YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_SingleParam->LeftToothNumSpace,1);           
        YY_SingleParam->LeftToothLengthINCHSpace =  YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_SingleParam->LeftToothNumSpace,1);
        
        YY_SingleParam->RightToothLengthCMSpace = YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_SingleParam->RightToothNumSpace,1);   
        YY_SingleParam->RightToothLengthINCHSpace =  YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_SingleParam->RightToothNumSpace,1);
        
        YY_GroupParam->AllSetLength = 0;
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->AllSetLength += YY_ToothNumCalLength(YY_SingleToothLength,(YY_GroupParam->LeftToothNum[i] + YY_GroupParam->LeftToothNumSpace[i]),YY_GroupParam->SetTotal[i]);
        }
        

        YY_SingleParam->SetLength = YY_ToothNumCalLength(YY_SingleToothLength,(YY_SingleParam->LeftToothNum + YY_SingleParam->LeftToothNumSpace),YY_SingleParam->SetTotal);

        
        YY_GroupParam->AllSetTotal = 0;
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->AllSetTotal += YY_GroupParam->SetTotal[i];
        }

        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothLengthCM[i] = YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_GroupParam->LeftToothNum[i],1);
        }
        
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothLengthCMSpace[i] = YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_GroupParam->LeftToothNumSpace[i],1);
        }

        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothLengthINCH[i] = YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_GroupParam->LeftToothNum[i],1);
        }
        
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothLengthINCHSpace[i] = YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_GroupParam->LeftToothNumSpace[i],1);
        }
        
    }
   
    if(YY_bCalInputLength)
    {
        YY_bCalInputLength = 0;
        
        YY_SingleParam->LeftToothLengthINCH = YY_ToothLengthCMCalInch(YY_SingleToothLength,YY_SingleParam->LeftToothLengthCM,1);
        YY_SingleParam->LeftToothNum          = YY_ToothLengthCMCalNum(YY_SingleToothLength,YY_SingleParam->LeftToothLengthCM,1); 
        
        YY_SingleParam->RightToothLengthINCH = YY_ToothLengthCMCalInch(YY_SingleToothLength,YY_SingleParam->RightToothLengthCM,1);
        YY_SingleParam->RightToothNum          = YY_ToothLengthCMCalNum(YY_SingleToothLength,YY_SingleParam->RightToothLengthCM,1); 

        YY_SingleParam->LeftToothLengthINCHSpace = YY_ToothLengthCMCalInch(YY_SingleToothLength,YY_SingleParam->LeftToothLengthCMSpace,1);
        YY_SingleParam->LeftToothNumSpace          = YY_ToothLengthCMCalNum(YY_SingleToothLength,YY_SingleParam->LeftToothLengthCMSpace,1); 
        
        YY_SingleParam->RightToothLengthINCHSpace = YY_ToothLengthCMCalInch(YY_SingleToothLength,YY_SingleParam->RightToothLengthCMSpace,1);
        YY_SingleParam->RightToothNumSpace          = YY_ToothLengthCMCalNum(YY_SingleToothLength,YY_SingleParam->RightToothLengthCMSpace,1); 
       
        
        YY_GroupParam->AllSetLength = 0;
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->AllSetLength += YY_LengthCalLengthM(YY_GroupParam->LeftToothLengthCM[i],YY_GroupParam->LeftToothLengthCMSpace[i],YY_GroupParam->SetTotal[i]);
        }
        
        YY_SingleParam->SetLength = YY_ToothNumCalLength(YY_SingleToothLength,(YY_SingleParam->LeftToothNum + YY_SingleParam->LeftToothNumSpace),YY_SingleParam->SetTotal);
        
        YY_GroupParam->AllSetTotal = 0;
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->AllSetTotal += YY_GroupParam->SetTotal[i];
        }
       
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothNum[i] = YY_ToothLengthCMCalNum(YY_SingleToothLength,YY_GroupParam->LeftToothLengthCM[i],1);
        }
        
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothNumSpace[i] = YY_ToothLengthCMCalNum(YY_SingleToothLength,YY_GroupParam->LeftToothLengthCMSpace[i],1);
        }

        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothLengthINCH[i] = YY_ToothLengthCMCalInch(YY_SingleToothLength,YY_GroupParam->LeftToothLengthCMSpace[i],1);
        }
        
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothLengthINCHSpace[i] = YY_ToothLengthCMCalInch(YY_SingleToothLength,YY_GroupParam->LeftToothLengthCMSpace[i],1);
        }
        
        YY_bCalInputToothNum = 1;
    }
    
    if(YY_bCalInputLengthInch)
    {
        YY_bCalInputLengthInch = 0;
          
        YY_SingleParam->LeftToothLengthCM     = YY_ToothLengthInchCalCM(YY_SingleToothLength,YY_SingleParam->LeftToothLengthINCH,1);
        YY_SingleParam->LeftToothNum             = YY_ToothLengthInchCalNum(YY_SingleToothLength,YY_SingleParam->LeftToothLengthINCH,1);
        
        YY_SingleParam->RightToothLengthCM     = YY_ToothLengthInchCalCM(YY_SingleToothLength,YY_SingleParam->RightToothLengthINCH,1);
        YY_SingleParam->RightToothNum             = YY_ToothLengthInchCalNum(YY_SingleToothLength,YY_SingleParam->RightToothLengthINCH,1);
        
        YY_SingleParam->LeftToothLengthCMSpace     = YY_ToothLengthInchCalCM(YY_SingleToothLength,YY_SingleParam->LeftToothLengthINCHSpace,1);
        YY_SingleParam->LeftToothNumSpace        = YY_ToothLengthInchCalNum(YY_SingleToothLength,YY_SingleParam->LeftToothLengthINCHSpace,1);
        
        YY_SingleParam->RightToothLengthCMSpace     = YY_ToothLengthInchCalCM(YY_SingleToothLength,YY_SingleParam->RightToothLengthINCHSpace,1);
        YY_SingleParam->RightToothNumSpace          = YY_ToothLengthInchCalNum(YY_SingleToothLength,YY_SingleParam->RightToothLengthINCHSpace,1);
        
        YY_GroupParam->AllSetLength = 0;
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->AllSetLength += YY_InchLengthCalLength(YY_GroupParam->LeftToothLengthINCH[i],YY_GroupParam->LeftToothLengthINCHSpace[i],YY_GroupParam->SetTotal[i]);
        }
        
        YY_SingleParam->SetLength = YY_ToothNumCalLength(YY_SingleToothLength,(YY_SingleParam->LeftToothNum + YY_SingleParam->LeftToothNumSpace),YY_SingleParam->SetTotal);
        
        YY_GroupParam->AllSetTotal = 0;
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->AllSetTotal += YY_GroupParam->SetTotal[i];
        }    
        
         for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothNum[i] = YY_ToothLengthInchCalNum(YY_SingleToothLength,YY_GroupParam->LeftToothLengthINCH[i],1);
        }
        
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothNumSpace[i] = YY_ToothLengthInchCalNum(YY_SingleToothLength,YY_GroupParam->LeftToothLengthINCHSpace[i],1);
        }

       for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothLengthCM[i] = YY_ToothLengthInchCalCM(YY_SingleToothLength,YY_GroupParam->LeftToothLengthINCH[i],1);
        }
        
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->LeftToothLengthCMSpace[i] = YY_ToothLengthInchCalCM(YY_SingleToothLength,YY_GroupParam->LeftToothLengthINCHSpace[i],1);
        }
        
        YY_bCalInputToothNum = 1;
    }
    
    if(YY_bCalculateTotal)	 //下一程序周期计算长度的时间
    {
        YY_bCalculateTotal = 0;   //  清通知位	
        
        total_buff  = 0;
        
        for(i = 0;i < 5;i++)
        {
            total_buff += YY_GroupParam->SetTotal[i];
        }
        
        if(YY_GroupParam->AllSetTotal > total_buff)YY_GroupParam->AllSetTotal = total_buff;
          
        YY_cTotal_Time();  
    }
    
    if(YY_bCalAllLength)
    {
        YY_bCalAllLength = 0;
        
        YY_GroupParam->AllSetLength = 0;
        for(i = 0;i < 5;i++)
        {
            YY_GroupParam->AllSetLength += YY_ToothNumCalLength(YY_SingleToothLength,(YY_GroupParam->LeftToothNum[i] + YY_GroupParam->LeftToothNumSpace[i]),YY_GroupParam->SetTotal[i]);
        }
        

        YY_SingleParam->SetLength = YY_ToothNumCalLength(YY_SingleToothLength,(YY_SingleParam->LeftToothNum + YY_SingleParam->LeftToothNumSpace),YY_SingleParam->SetTotal);
    }
    
    if(YY_bClear1)
    {
        YY_bClear1 = 0;
        YY_GroupParam->OverSetTotal[0]        = 0;
        YY_GroupParam->DisplyLeftToothLengthCM[0]  = 0;
        YY_GroupParam->DisplyLeftToothLengthCMSpace[0] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCHSpace[0] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCH[0] = 0;
        
        YY_GroupParam->DisplyRightToothNum[0]  = 0;
        YY_GroupParam->DisplyRightToothNumSpace[0]   = 0;
    }

    if(YY_bClear2)
    {
        YY_bClear2 = 0;
        YY_GroupParam->OverSetTotal[1]        = 0;
        YY_GroupParam->DisplyLeftToothLengthCM[1]  = 0;
        YY_GroupParam->DisplyLeftToothLengthCMSpace[1] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCHSpace[1] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCH[1] = 0;
        
        YY_GroupParam->DisplyRightToothNum[1]  = 0;
        YY_GroupParam->DisplyRightToothNumSpace[1]   = 0;
    }    
 
    if(YY_bClear3)
    {
        YY_bClear3 = 0;
        YY_GroupParam->OverSetTotal[2]        = 0;
        YY_GroupParam->DisplyLeftToothLengthCM[2]  = 0;
        YY_GroupParam->DisplyLeftToothLengthCMSpace[2] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCHSpace[2] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCH[2] = 0;
        
        YY_GroupParam->DisplyRightToothNum[2]  = 0;
        YY_GroupParam->DisplyRightToothNumSpace[2]   = 0;
    }

    if(YY_bClear4)
    {
        YY_bClear4 = 0;
        YY_GroupParam->OverSetTotal[3]        = 0;
        YY_GroupParam->DisplyLeftToothLengthCM[3]  = 0;
        YY_GroupParam->DisplyLeftToothLengthCMSpace[3] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCHSpace[3] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCH[3] = 0;
        
        YY_GroupParam->DisplyRightToothNum[3]  = 0;
        YY_GroupParam->DisplyRightToothNumSpace[3]   = 0;
    }   
    
    if(YY_bClear5)
    {
        YY_bClear5 = 0;
        YY_GroupParam->OverSetTotal[4]        = 0;
        YY_GroupParam->DisplyLeftToothLengthCM[4]  = 0;
        YY_GroupParam->DisplyLeftToothLengthCMSpace[4] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCHSpace[4] = 0;
        YY_GroupParam->DisplyLeftToothLengthINCH[4] = 0;
        
        YY_GroupParam->DisplyRightToothNum[4]  = 0;
        YY_GroupParam->DisplyRightToothNumSpace[4]   = 0;
    }   
}

void YY_StartZYFirst(void)
{
    YY_ZYBuff = YY_SystemParam->StartOilTime;	
    YY_bFirstZY  = 1;   //M100  倒时显示
    YY_bZhuYou   = 1;
    YY_ZYDelay = dwTickCount + 1000;
    YY_OIL_MOTOR = 1;
    YY_DISPLAY_STATE = 1;
    YY_OilCheckDelay = dwTickCount + 2500;
}

void YY_ZhuYou(void)
{
    if(YY_OIL_MOTOR)
    {
        if((dwTickCount >= YY_ZYDelay) || (YY_bZhuYou == 0))
        { 
            if(YY_bFirstZY)
            {
                YY_ZYDelay = dwTickCount + 1000;
                if(YY_SystemParam->StartOilTime)
                {
                    YY_SystemParam->StartOilTime--;
                }
                if((YY_SystemParam->StartOilTime == 0) || (YY_bZhuYou == 0))	//初次注油完成
                {
                    YY_bFirstZY = 0;   //M100	
                    YY_OIL_MOTOR = 0;	 //注油机关
                    YY_SystemParam->StartOilTime = YY_ZYBuff;
                    YY_ZYDelay = dwTickCount + YY_SystemParam->IntOilTime * 60 * 1000; 
                    YY_DISPLAY_STATE = 2;  //注油完成
                }	
            }
            else
            {
                YY_OIL_MOTOR = 0; //注油机关
                if(YY_bZhuYou)
                        YY_ZYDelay = dwTickCount + YY_SystemParam->IntOilTime * 60 * 1000;   //间隔注油时间  分钟
                else 
                        YY_ZYDelay = dwTickCount;
            }
            YY_bZYNow = 0;   //M8  清通知位
        } 
    }
    else if(YY_bZhuYou && ((dwTickCount >= YY_ZYDelay) || YY_bZYNow) && YY_EGMSTOP_IN)
    {
        //大于1小时,重新先注油
        if(((dwTickCount - YY_ZYDelay) > (3600 * 1000)) && (dwTickCount >= YY_ZYDelay))
        {
                YY_StartZYFirst();
        }
        else
        {
                YY_OIL_MOTOR = 1;
                YY_ZYDelay = dwTickCount + YY_SystemParam->OilTime * 1000;   //注油时间  秒
                YY_OilCheckDelay = dwTickCount + (unsigned long)2500;    //延时检测油压
        }
        YY_bZYNow = 0;   //M8  清通知位	
    }  
}

//手动动作
void YYa_ManualAction(void)
{  
    //合链机启动
    if(YY_bHL)   
    {
        if(YY_HL_DW_IN)
        {
            YY_HL_MOTOR = 1;
        }
        else if(YY_HL_UP_IN)
        {
            YY_HL_MOTOR = 0;        
        }
    }
    else
    {
        YY_HL_MOTOR = 0;
    }
        
    if(YY_bPYMotor)
    {
        YY_bPYMotor = 0;
        
        if(YY_MAIN_MOTOR)
        {
            if(!YY_bRunning)YY_bPYControl = 0;
        }
        else if(YY_bZhuYou && !YY_bOnceStartPower) YY_bPYControl = 1;       
    }
    
    if(YY_bPYControl)
    {
        if(YY_MAIN_MOTOR == 0)
        {
            YY_CheckDelay = dwTickCount + 1000;	
            YY_OIL_MOTOR  = 1;
            YY_ZhuYouDelay = dwTickCount + 1000*YY_SystemParam->OilTime;	
            YY_CheckDelay  = dwTickCount + 2500;
        }
        YY_MAIN_MOTOR = 1;
    }
    else
    {
        if(YY_MAIN_MOTOR)
        {
            YY_CheckDelay = dwTickCount + 1000;	
        }
        YY_MAIN_MOTOR = 0; 
    }
    
    if(YY_bClearTotal)
    {
        YY_bClearTotal = 0;
        switch(YY_bMode)
        {
            case YY_SINGLE_MODE:
            {
                YY_SystemParam->AllProductTime += YY_SingleParam->SetTimeHour;
                YY_SystemParam->AllProductTime += YY_SingleParam->SetTimeMinute/60;
                YY_SingleParam->OverTotal = 0;
                YY_SingleParam->OverLength = 0;
                YY_SingleParam->SetTimeHour = 0;
                YY_SingleParam->SetTimeMinute = 0;
            }break;
            case YY_GROUP_MODE:
            {
                YY_SystemParam->AllProductTime += YY_GroupParam->SetTimeHour;
                YY_SystemParam->AllProductTime += YY_GroupParam->SetTimeMinute/60;              
                YY_GroupParam->AllOverTotal = 0;
                YY_GroupParam->AllOverLength = 0;
                YY_GroupParam->SetTimeHour = 0;
                YY_GroupParam->SetTimeMinute = 0;            
            }break;
            
        }
        YY_cTotal = 0;
    }
    
    if(YY_bClearPro)
    {
        YY_bClearPro = 0;
        YY_SystemParam->AllProductTime = 0;
        YY_SystemParam->AllProductLength = 0;
    }
    
    if(!YY_bRunning)
    {
        if((YY_bChangeNextGroup) &&  (YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup] == 0) && (YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup] == 0))
        {
            YY_bChangeNextGroup = 0;
            YY_SystemParam->NowGroup = YY_SystemParam->NextGroupBuff - 1;
        }
        
        
        if(YY_bReset)
        {
            YY_bReset = 0;
            switch(YY_bMode)
            {
                case YY_SINGLE_MODE:
                {
                    YY_ReSetData();
                }break;
                case YY_GROUP_MODE:
                {
                    YY_ReSetData();
                }break;
            }
        }
    }
    
        //故障清除              
    if(YY_bClearAlarm)
    {
        if(YY_SystemParam->AlarmCode& YY_TOOTH_NUM_ALARM)	 //叠牙时直接打空位
        {
            YY_ReSetData();		 //6空位，6牙
        }
        YY_ALARM_LED = 0;
        YY_SystemParam->AlarmCode = 0;
        YY_bClearAlarm = 0;
    }
    
    if(YY_bSetDCTEnable)
    {
        YY_bSetDCTEnable = 0;
        if(YY_bDCTEnable)
        {
            YY_SingleParam->DisplyLeftToothNum    = 0;
            YY_SingleParam->DisplyLeftToothLengthCM = 0; 
            YY_SingleParam->DisplyLeftToothLengthINCH = 0; 
            YY_SingleParam->DisplyLeftToothNumSpace     = 0; 
            YY_SingleParam->DisplyLeftToothLengthCMSpace = 0; 
            YY_SingleParam->DisplyLeftToothLengthINCHSpace = 0; 
            YY_SingleParam->DisplyRightToothNum = 0;       
            YY_SingleParam->DisplyRightToothLengthCM = 0; 
            YY_SingleParam->DisplyRightToothLengthINCH = 0; 
            YY_SingleParam->DisplyRightToothNumSpace = 0;       
            YY_SingleParam->DisplyRightToothLengthCMSpace = 0;  
            YY_SingleParam->DisplyRightToothLengthINCHSpace =  0;
            YY_cStartPYFlag_Left  = 1;
            YY_cStartPYFlag_Right = 1;        
        }
        else
        {
              YY_cStartPYFlag_Left  = 0;
              YY_cStartPYFlag_Right = 0;
              YY_SingleParam->DisplyLeftToothNum    = 0;
              YY_SingleParam->DisplyLeftToothLengthCM = 0; 
              YY_SingleParam->DisplyLeftToothLengthINCH = 0; 
              YY_SingleParam->DisplyLeftToothNumSpace     = 0; 
              YY_SingleParam->DisplyLeftToothLengthCMSpace = 0; 
              YY_SingleParam->DisplyLeftToothLengthINCHSpace = 0; 
              YY_SingleParam->DisplyRightToothNum = 0;       
              YY_SingleParam->DisplyRightToothLengthCM = 0; 
              YY_SingleParam->DisplyRightToothLengthINCH = 0; 
              YY_SingleParam->DisplyRightToothNumSpace = 0;       
              YY_SingleParam->DisplyRightToothLengthCMSpace = 0;  
              YY_SingleParam->DisplyRightToothLengthINCHSpace =  0;
              YY_SetLeftDCTSpace();
              YY_SetRightDCTSpace();       
        }
    }
    
    YY_CalculataParam();
}

//拉链接头控制处理

void YY_JieTouControl(void)
{
    //接头检测
    if(YY_JT_IN_UP)	//空位
    {
        YY_cJieDaiTotal = YY_SystemParam->JieTouMJToothNum;	
        YY_cJieDaiClrTotal = 0;
        YY_cJieDaiState = 1;

    }
    else if(YY_JT_IN_DW)
    {
        YY_cJieDaiState = 2;
        if(YY_cJieDaiTotal == 0)
        {
            YY_cJieDaiTotal = YY_SystemParam->JieTouMJToothNum;	
        }
        else
        {	

        }
    }
}

void YY_CountYaError(void)
{
    unsigned short i;
    switch(YY_bMode)
    {
        case YY_SINGLE_MODE:
        {
            //数牙出错
 /*          if(UserParam->LeftOverToothNum || UserParam->RightOverToothNum)
            {
                if(UserParam->LeftOverToothNum >= UserParam->RightOverToothNum)
                {
                        i = UserParam->LeftOverToothNum - UserParam->RightOverToothNum;	
                }
                else 
                        i = UserParam->RightOverToothNum - UserParam->LeftOverToothNum; 
                                        //   正常打牙状态
                if((i > 2) && (((i < (UserParam->LeftSetNum-1)) && (cStartPYFlag_Right == 0)) 
                //	  复位打牙状态
                ||(cStartPYFlag_Right && (i < 5))))			 
                                                                        
                {
                        M88 = 1;   //M88  数牙出错
                        ALARM_CODE = 88;
                        
                        if(Y017 == 0)Y16 = 1;
                        
                }
            }
            else if((UserParam->LeftOverKongWei || UserParam->RightOverKongWei) && UserParam->LeftSetKongWei)
            {
                if(UserParam->LeftOverKongWei >= UserParam->RightOverKongWei)
                {
                        i = UserParam->LeftOverKongWei - UserParam->RightOverKongWei;	
                }
                else 
                        i = UserParam->RightOverKongWei - UserParam->LeftOverKongWei;
                if((i > 2) && (i != UserParam->LeftSetKongWei))	
                {
                        M88 = 1;   //M88  数牙出错
                        ALARM_CODE = 88;
                        if(Y16 == 0)Y017 = 1;
                        
                }
            }	*/	 
        }break;
        case YY_GROUP_MODE:
        {
                   //数牙出错
            if(YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup] || YY_GroupParam->DisplyRightToothNum[YY_SystemParam->NowGroup])
            {
                if(YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup] >= YY_GroupParam->DisplyRightToothNum[YY_SystemParam->NowGroup])
                {
                        i = YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup] - YY_GroupParam->DisplyRightToothNum[YY_SystemParam->NowGroup];	
                }
                else 
                        i = YY_GroupParam->DisplyRightToothNum[YY_SystemParam->NowGroup] - YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup]; 
                                        //   正常打牙状态
                if((i > 2) && (((i < (YY_GroupParam->LeftToothNum[YY_SystemParam->NowGroup]-1)) && (YY_cStartPYFlag_Right == 0)) 
                //	  复位打牙状态
                ||(YY_cStartPYFlag_Right && (i < 5))))			                                                                        
                {
                      
                        YYa_SetAlarmCode(YY_TOOTH_NUM_ALARM);
                        if(Y017 == 0)Y16 = 1;
                        
                }
            }
            else if((YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup] || YY_GroupParam->DisplyRightToothNumSpace[YY_SystemParam->NowGroup]) && YY_GroupParam->LeftToothNumSpace[YY_SystemParam->NowGroup])
            {
                if(YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup] >= YY_GroupParam->DisplyRightToothNumSpace[YY_SystemParam->NowGroup])
                {
                        i = YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup] - YY_GroupParam->DisplyRightToothNumSpace[YY_SystemParam->NowGroup];	
                }
                else 
                        i = YY_GroupParam->DisplyRightToothNumSpace[YY_SystemParam->NowGroup] - YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup];
                if((i > 2) && (i != YY_GroupParam->LeftToothNumSpace[YY_SystemParam->NowGroup]))	
                {
                        YYa_SetAlarmCode(YY_TOOTH_NUM_ALARM);
                        if(Y16 == 0)Y017 = 1;
                        
                }
            }		        
        }break;        
    }
}

void YY_RefreshLengthInch(void)
{   
    unsigned char i;
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      { 
          YY_SingleParam->DisplyLeftToothLengthCM   = YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_SingleParam->DisplyLeftToothNum,1);
          YY_SingleParam->DisplyLeftToothLengthCMSpace   = YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_SingleParam->DisplyLeftToothNumSpace,1);
          YY_SingleParam->DisplyRightToothLengthCM   = YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_SingleParam->DisplyRightToothNum,1);
          YY_SingleParam->DisplyRightToothLengthCMSpace   = YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_SingleParam->DisplyRightToothNumSpace,1);
          YY_SingleParam->DisplyLeftToothLengthINCH   = YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_SingleParam->DisplyLeftToothNum,1);
          YY_SingleParam->DisplyLeftToothLengthINCHSpace   = YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_SingleParam->DisplyLeftToothNumSpace,1);
          YY_SingleParam->DisplyRightToothLengthINCH   = YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_SingleParam->DisplyRightToothNum,1);
          YY_SingleParam->DisplyRightToothLengthINCHSpace   = YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_SingleParam->DisplyRightToothNumSpace,1);
      }break;
      case YY_GROUP_MODE:
      {
          for(i=0;i < 5;i++)
          {
              YY_GroupParam->DisplyLeftToothLengthCM[i]   =  YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_GroupParam->DisplyLeftToothNum[i],1);
              YY_GroupParam->DisplyLeftToothLengthCMSpace[i] =  YY_ToothNumCalLengthCM(YY_SingleToothLength,YY_GroupParam->DisplyLeftToothNumSpace[i],1); 
              YY_GroupParam->DisplyLeftToothLengthINCH[i]=  YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_GroupParam->DisplyLeftToothNum[i],1);
              YY_GroupParam->DisplyLeftToothLengthINCHSpace[i] =  YY_ToothNumCalLengthInch(YY_SingleToothLength,YY_GroupParam->DisplyLeftToothNumSpace[i],1); 
          }
      }break;
    } 
}

void YY_ReFreshRemainLife(void)
{
    unsigned char i;
    
    for(i=0;i<16;i++)
    {
        YY_ComponentParam->RemainLife[i] = YY_ComponentParam->LeftRightLife[i] -  YY_ComponentParam->LeftRightUsedLife[i];
    }
}

void YY_DisplayStateRefresh(void)
{
    unsigned char i;
    switch(YY_bMode)
    {
        case YY_SINGLE_MODE:
        {
             
        }break;
        case YY_GROUP_MODE:
        {
            if(YY_bRunning)
            {
                 for(i=0;i<5;i++)
                 {
                     if(i==YY_SystemParam->NowGroup)YY_SystemParam->TotalDisplayState[i] = 1;
                     else
                     {
                         if(YY_GroupParam->OverSetTotal[i] < YY_GroupParam->SetTotal[i])
                         {
                             YY_SystemParam->TotalDisplayState[i] = 0;//待加工组
                         }
                         else
                         {
                             YY_SystemParam->TotalDisplayState[i] = 2;//已完成组
                         } 
                     }
                 }            
            }
            else
            {
                 for(i=0;i<5;i++)
                 {
                     if(i==(YY_SystemParam->NextGroupBuff - 1))YY_SystemParam->TotalDisplayState[i] = 1;
                     else
                     {
                         if(YY_GroupParam->OverSetTotal[i] < YY_GroupParam->SetTotal[i])
                         {
                             YY_SystemParam->TotalDisplayState[i] = 0;//待加工组
                         }
                         else
                         {
                             YY_SystemParam->TotalDisplayState[i] = 2;//已完成组
                         } 
                     }
                 }     
            }            
        }break;
    }
}

//错误停机
void YY_Error_Action(void)
{ 
    static unsigned long tx_cnt = 0;
    if(YY_EGMSTOP_IN == 0) //紧急停止
    {
        YYa_SetAlarmCode(YY_EGM_ALARM);
    }
    
    if(dwTickCount >= YY_ErrorDelay)
    {
        if(YY_YW_IN)		//液位警告
        {
             YYa_SetAlarmCode(YY_OIL_VOLUME_ALARM);
        }
        if(YY_TX_IN)		//铜线故障
        {
            tx_cnt++;
            if(tx_cnt > 1000)
            {
               YYa_SetAlarmCode(YY_TONG_XIAN_ALARM);
            }
        }
        else
           tx_cnt = 0;
        if(YY_CX_IN && YY_MAIN_MOTOR)  //叠牙
        {
           YYa_SetAlarmCode(YY_CHENG_XING_ALARM);
        }
        if(YY_KD_IN)  //卡带故障(布带1)
        {
            YYa_SetAlarmCode(YY_KA_DAI_ALARM);
        }
        if(YY_ZIPPER_IN)  //没带故障(布带2)
        {
            YYa_SetAlarmCode(YY_QUE_DAI_ALARM);
        }

        if(YY_HL_LIMIT_IN)  //合链上限、下限位开关（合链1）
        {
            YYa_SetAlarmCode(YY_JIN_LIAN_ALARM);
        }
        
        if(dwTickCount >= YY_OilCheckDelay)
        {
            YY_OilCheckDelay= dwTickCount+ 100;
            //油压不到警告
            if(YY_OIL_MOTOR)
            {
                if(YY_YY_IN)
                {
                    YYa_SetAlarmCode(YY_OIL_PRESSURE_ALARM);
                }
            }
        }
        
        YY_CountYaError();
        YY_RefreshLengthInch();
        YY_ReFreshRemainLife();
        YY_DisplayStateRefresh();
        
    }
}
void YYa_AlarmProtect(void)
{ 
    YY_Error_Action();
        //旋转电磁铁动作
    if((YY_LEFT_IN || YY_LEFT_OUT) && (dwTickCount >= YY_LCntDelay))	 //左边
    {
        YY_LEFT_IN = 0;
        YY_LEFT_OUT = 0;
    }
    if((YY_RIGHT_IN || YY_RIGHT_OUT) && (dwTickCount >= YY_RCntDelay))	 //右边
    {
        YY_RIGHT_IN = 0;
        YY_RIGHT_OUT = 0;
    }	
}

//检测现在加工是否会换组
unsigned short YY_CheckHaveChangeGroup(void)
{
     switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
           return 0;
      }break;
      case YY_GROUP_MODE:
      {   
          if(YY_GroupParam->OverSetTotal[YY_SystemParam->NowGroup] == (YY_GroupParam->SetTotal[YY_SystemParam->NowGroup] - 1))
                return 1;
          else
                return 0;

      }break;
          default:return 0;
    }        
}

//检测剩余齿数够不够完成拉链
unsigned short YY_CheckRemainToothOk(void)
{
     unsigned short toothbuff1,toothbuff2;
     switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
           if(((YY_SingleParam->LeftToothNum+YY_SingleParam->LeftToothNumSpace) - (YY_SingleParam->DisplyLeftToothNum+YY_SingleParam->DisplyLeftToothNumSpace)) <= YY_cJieDaiTotal)
           {             
               return 1;
           }
           else
           {
               return 0;
           }
      }break;
      case YY_GROUP_MODE:
      {   
          toothbuff1 = YY_GroupParam->LeftToothNum[YY_SystemParam->NowGroup] + YY_GroupParam->LeftToothNumSpace[YY_SystemParam->NowGroup];
          toothbuff2 = YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup] + YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup];
          if(YY_CheckHaveChangeGroup())
          {
              if((toothbuff1 - toothbuff2 + YY_SystemParam->DifferentLengthToothNum) <= YY_cJieDaiTotal)
              {
                  return 1;
              }
              else
              {
                  return 0;
              }          
          }
          else
          {
              if((toothbuff1 - toothbuff2) <= YY_cJieDaiTotal)
              {
                  return 1;
              }
              else
              {
                  return 0;
              }
          }
      }break;
      default:return 0;
    }    
}

unsigned short YY_FindNextUserFulGroup(unsigned short now_group)
{
    unsigned char i;
    
    for(i=(now_group + 1);i<5;i++)
    {
       if((YY_GroupParam->OverSetTotal[i] < YY_GroupParam->SetTotal[i]) && (YY_GroupParam->SetTotal[i] != 0)) return i;
    }
    
    for(i=0;i<now_group;i++)
    {
       if((YY_GroupParam->OverSetTotal[i] < YY_GroupParam->SetTotal[i]) && (YY_GroupParam->SetTotal[i] != 0)) return i;
    }
    
    return 99;
}

void YY_ChangeGroupControlLeft(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {

      }break;
      case YY_GROUP_MODE:
      {         
           if(YY_GroupParam->SetTotal[YY_SystemParam->NowGroup] != 0)
           {
                if(YY_GroupParam->OverSetTotal[YY_SystemParam->NowGroup] < YY_GroupParam->SetTotal[YY_SystemParam->NowGroup])
                {
               
                }
                else
                {
                  if(YY_FindNextUserFulGroup(YY_SystemParam->NowGroup) != 99)
                  {
                    YY_SetLeftPyData(0,YY_SystemParam->DifferentLengthToothNum);
                    YY_SetRightPyData(0,YY_SystemParam->DifferentLengthToothNum);
                    YY_cStartPYFlag_Left  = 1;
                    YY_cStartPYFlag_Right = 1;

                    YY_SystemParam->NowGroup = YY_FindNextUserFulGroup(YY_SystemParam->NowGroup);

                  }
                }                 
           }
      }
    }
}

//搜索全部做完没有
unsigned long YY_FindCanWorkNum(void)
{
    unsigned char i;
    
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
           return 1;
      }break;
      case YY_GROUP_MODE:
      {   
          for(i=0;i < 5;i++)
          {
              if(YY_GroupParam->OverSetTotal[i] < YY_GroupParam->SetTotal[i])return 1;
          }
          
          return 0;          
      }break;
          default:return 0;
    }

}
//左边排牙动作
/*
当在按下复位时就先打6空位，再打6牙 
*/
void YY_Left_Action(void)
{      
     YY_DIAPLAY0 = YY_cTotal;
     YY_DIAPLAY1 = YY_GetSetTotal();
     YY_DIAPLAY2 = YY_FindCanWorkNum();

    if(YY_LEFT_COUNT_IN_UP && YY_bDCTEnable)
    { 
         YY_RightCountEnable = 0;
        
        if(YY_cJieDaiState == 1)
        {
            if(YY_cJieDaiTotal)
            {
                YY_cJieDaiClrTotal++;
            }
            else
                YY_cJieDaiClrTotal = 0;
        }    

        if(YY_cJieDaiTotal && YY_cJieDaiState)
        {   
              YY_cJieDaiTotal--;
            if(YY_cJieDaiTotal == 0)
            {
                YY_cStartPYFlag_Left  = 3;
                YY_cStartPYFlag_Right = 3;
                
                if(YY_GetLeftSpace() == 0)                      // 空位设定
                {
                    YY_SetLeftPyData(0,YY_cJieDaiClrTotal + 10 + YY_SystemParam->JieTouToothNum);
                    YY_SetRightPyData(0,YY_cJieDaiClrTotal + 10 +YY_SystemParam->JieTouToothNum);
                    YY_SetLeftSpaceDisplay(0);
                    YY_SetLeftDisplay(0);   
                    YY_SetRightSpaceDisplay(0);
                    YY_SetRightDisplay(0);
                    YY_cJieDaiState = 0;                   
                }
                else
                {
                    YY_SetLeftPyData(0,YY_cJieDaiClrTotal + 6 + YY_SystemParam->JieTouToothNum);
                    YY_SetRightPyData(0,YY_cJieDaiClrTotal + 6 + YY_SystemParam->JieTouToothNum);   
                    YY_SetLeftSpaceDisplay(0);
                    YY_SetLeftDisplay(0);
                    YY_SetRightSpaceDisplay(0);
                    YY_SetRightDisplay(0);
                    YY_cJieDaiState = 0;
                }
                
                if(YY_cJieDaiState == 2)YY_cJieDaiState = 0;	
                
                if(YY_bDCTEnable)
                {
                    YY_SetLeftDCTSpace();
                    YY_SetRightDCTSpace();
                }
            }
        }

        if(YY_NowLeftPyKongWei)
        {
            if(YY_cStartPYFlag_Left)
            {
                YY_cStartPYFlag_Left = 0;
                //变为空位，不用铜丝
                if(YY_bDCTEnable)
                {
                    YY_SetLeftDCTSpace();  
                }
            }

            YY_NowLeftPyKongWei--;
   

            if(YY_NowLeftPyKongWei == 0)YY_cStartPYFlag_Left = 1;
        }
        else if(YY_NowLeftPyNum)
        {
            if(YY_cStartPYFlag_Left && (YY_cOverTotalLeftFlg == 0))
            {
                YY_cStartPYFlag_Left = 0;
                
                if(YY_bDCTEnable)
                {
                //变为打牙，
                   YY_SetLeftDCTTooth();
                }
            }
            YY_NowLeftPyNum--;
            
            if(YY_NowLeftPyNum == 0)
            {
                YY_cStartPYFlag_Left = 1;
                YY_cOverTotalLeftFlg = 0;
            }
        }
        else if(YY_GetLeftToothNum() > YY_GetLeftToothNumDisplay())  //打齿状态
        {
             if(YY_cStartPYFlag_Left)
            {
                YY_cStartPYFlag_Left = 0;
                
                if(YY_bDCTEnable)
                {
                    //变为打牙，
                    YY_SetLeftDCTTooth(); 
                }

            }
            
            YY_LeftToothDisplayAdd();
            
            if(YY_cJieDaiState)
            {
                if(YY_GetLeftSpace() != 0)
                {
                    if(YY_CheckRemainToothOk())
                    { 	

                    }
                    else
                    {
                         YY_SetLeftPyData(0,YY_cJieDaiTotal); 
                         YY_SetLeftSpaceDisplay(0);
                         YY_SetLeftDisplay(0);
                         
                         YY_SetRightPyData(0,YY_cJieDaiTotal); 
                         YY_SetRightSpaceDisplay(0);
                         YY_SetRightDisplay(0);
                         
                         YY_cStartPYFlag_Left = 1; 
                         YY_cStartPYFlag_Right = 1;  
                    }
                }

            }
   
            if(YY_GetLeftToothNum() == YY_GetLeftToothNumDisplay())  //打完齿
            {
                YY_cStartPYFlag_Left  = 1;   
                YY_LeftOverSet(); 
                if(YY_GetLeftSpace() == 0)
                {
                    if(YY_bChangeNextGroup)
                    {
                        YY_bChangeNextGroup = 0;
                        YY_SystemParam->NowGroup = YY_SystemParam->NextGroupBuff - 1;

                        YY_SetLeftPyData(0,YY_SystemParam->DifferentLengthToothNum);
                        YY_SetRightPyData(0,YY_SystemParam->DifferentLengthToothNum);
                        YY_cStartPYFlag_Left  = 1;
                        YY_cStartPYFlag_Right = 1;
                    }
                    
                    YY_ChangeGroupControlLeft();  
                    
                    YY_SetLeftSpaceDisplay(0);
                    YY_SetLeftDisplay(0);                     
                }
                              //按停止 或产量到
                if(YY_bSingStop || (YY_cTotal >= YY_GetSetTotal()) || (YY_FindCanWorkNum() == 0))
                {
                    if(YY_GetLeftSpace() == 0)
                    {
                        if((YY_cTotal >= YY_GetSetTotal()) || (YY_FindCanWorkNum() == 0))
                        {
                                YY_SetLeftPyData(10,YY_SystemParam->DifferentLengthToothNum);
                                YY_SetRightPyData(10,YY_SystemParam->DifferentLengthToothNum);
                                YY_cStartPYFlag_Left  = 1;
                                YY_cStartPYFlag_Right = 1;   
                                
                                YY_cOverTotalRightFlg = 1;
                                YY_cOverTotalLeftFlg  = 1;
                        }
                    }
                   
                    YY_Stop_Action();
                    if(YY_bSingStop == 0)YY_DISPLAY_STATE = 4;
                }
                YY_LeftOk = 0;
            }  
        } 
        else if(YY_GetLeftSpace() > YY_GetLeftSpaceDisplay())  //空位状态
        {                       
            if(YY_cStartPYFlag_Left)
            {
                YY_cStartPYFlag_Left = 0;
                if(YY_bDCTEnable)
                {
                    //变为空位，不用铜丝
                    YY_SetLeftDCTSpace();  
                }
             }
           
            YY_LeftSpaceDisplayAdd();
                             
            if(YY_GetLeftSpace() == YY_GetLeftSpaceDisplay())
            {                
                 //只有大于一条拉链时才打牙状态
                if(YY_cJieDaiState)
                {
                     if(YY_CheckRemainToothOk())
                    { 	

                    }
                    else
                    {
                        if(YY_cJieDaiState != 0)
                        {
                             YY_SetLeftPyData(0,YY_cJieDaiTotal); 
                             YY_SetLeftSpaceDisplay(0);
                             YY_SetLeftDisplay(0);
                             
                             YY_SetRightPyData(0,YY_cJieDaiTotal); 
                             YY_SetRightSpaceDisplay(0);
                             YY_SetRightDisplay(0);
                        }                                                   
                    }                
                }
                
                YY_SetLeftSpaceDisplay(0);
                YY_SetLeftDisplay(0);                
                YY_cStartPYFlag_Left = 1; 
                YY_LeftOk = 1;
                if(YY_ChangeNextGroupFlg && YY_RightOk)
                {
                    YY_RightOk = 0;
                    YY_LeftOk  = 0;
                    YY_ChangeNextGroupFlg = 0;
                    YY_SetLeftSpaceDisplay(0);
                    YY_SetLeftDisplay(0);       
                    if(YY_bChangeNextGroup)
                    {
                        YY_bChangeNextGroup = 0;
                        YY_SystemParam->NowGroup = YY_SystemParam->NextGroupBuff - 1;

                        YY_SetLeftPyData(0,YY_SystemParam->DifferentLengthToothNum);
                        YY_SetRightPyData(0,YY_SystemParam->DifferentLengthToothNum);
                        YY_cStartPYFlag_Left  = 1;
                        YY_cStartPYFlag_Right = 1;
                    }
                    
                    YY_ChangeGroupControlLeft();                           
                }   
 
               
            }
        }

        
            //如叠牙或数牙导常的情况下，不能送牙
        if((YY_SystemParam->AlarmCode == YY_CHENG_XING_ALARM) || (YY_SystemParam->AlarmCode == YY_TOOTH_NUM_ALARM)  || !YY_bDCTEnable)// || M81 || M80)
        {
            YY_SetLeftDCTSpace(); 
        }
        
        YY_ProOnceTime = dwTickCount - YY_CalProcessDelay;	  //计算时间			
        YY_CalProcessDelay = dwTickCount;
    }

}

void YY_LeftOverSet(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          //产量计数
          //当两边的齿都打完时，产量加1
           if(YY_cTatal_OK)
          {
              YY_cTatal_OK = 0;
              YY_cTotal++;
              YY_AddTotal();
              YY_CalUseLifeFlg = 1;
              YY_bCalculateTotal = 1;
          }
          else
                  YY_cTatal_OK = 1;
      }break;
      case YY_GROUP_MODE:
      {
          //产量计数
          //当两边的齿都打完时，产量加1
          if(YY_cTatal_OK)
          {
              YY_cTatal_OK = 0;
              YY_cTotal++;
              YY_AddTotal();
              YY_CalUseLifeFlg = 1;
              YY_bCalculateTotal = 1;
              YY_SaveParamFlg    = 1;
              YY_UseLifeNowGroup = YY_SystemParam->NowGroup;
              YY_LastGroup       = YY_SystemParam->NowGroup;   
              YY_ChangeNextGroupFlg = 1;
          }
          else
          {
              YY_cTatal_OK = 1;             
          }
   
      }break;
    }     
}

void YY_RightOverSet(void)
{
    //产量计数
     //当两边的齿都打完时，产量加1
    if(YY_cTatal_OK)
    {
        YY_cTatal_OK = 0;
        YY_cTotal++;
        YY_AddTotal();
        YY_CalUseLifeFlg = 1;
        YY_bCalculateTotal = 1;
        YY_UseLifeNowGroup = YY_SystemParam->NowGroup;
        YY_LastGroup       = YY_SystemParam->NowGroup; 
        YY_ChangeNextGroupFlg = 1;
    }
    else
    {
        YY_cTatal_OK = 1;
    }
}
void YY_Right_Action(void)
{ 
      
    if(YY_RIGHT_COUNT_IN_UP && (YY_RightCountEnable == 0) && YY_bDCTEnable)
    {        
        if(YY_NowRightPyKongWei)
        {
            if(YY_cStartPYFlag_Right)
            {
                YY_cStartPYFlag_Right = 0;
                
                if(YY_bDCTEnable)
                {
                    //变为空位，不用铜丝
                     YY_SetRightDCTSpace();  
                }
            }

            YY_NowRightPyKongWei--;
            
            if((YY_NowRightPyKongWei == 0))YY_cStartPYFlag_Right = 1;
        }
        else if(YY_NowRightPyNum)
        {
            if(YY_cStartPYFlag_Right && (YY_cOverTotalRightFlg == 0))
            {
                YY_cStartPYFlag_Right = 0;
                //变为打牙，
                if(YY_bDCTEnable)
                {
                    YY_SetRightDCTTooth();          
                }
            }

            YY_NowRightPyNum--;
            if(YY_NowRightPyNum == 0)
            {
                YY_cStartPYFlag_Right = 1;
                YY_cOverTotalRightFlg = 0;
            }
        }
        else if(YY_GetRightToothNum() > YY_GetRightToothNumDisplay())  //打齿状态
        {
             if(YY_cStartPYFlag_Right)
            {
                YY_cStartPYFlag_Right = 0;
                if(YY_bDCTEnable)
                {
                //变为打牙，
                    YY_SetRightDCTTooth();   
                }
            }
            
            YY_RightToothDisplayAdd();
            
            if(YY_GetRightToothNum() == YY_GetRightToothNumDisplay())  //打齿状态
            {
                YY_cStartPYFlag_Right  = 1;   
                
                YY_RightOverSet();
                
                if(YY_GetRightSpace() == 0)   
                {
                    YY_SetRightSpaceDisplay(0);
                    YY_SetRightDisplay(0);  
                    if(YY_bChangeNextGroup)
                    {
                        YY_bChangeNextGroup = 0;
                        YY_SystemParam->NowGroup = YY_SystemParam->NextGroupBuff - 1;

                        YY_SetLeftPyData(0,YY_SystemParam->DifferentLengthToothNum);
                        YY_SetRightPyData(0,YY_SystemParam->DifferentLengthToothNum);
                        YY_cStartPYFlag_Left  = 1;
                        YY_cStartPYFlag_Right = 1;
                    }
                    
                    YY_ChangeGroupControlLeft();  
                }

                        //按停止 或产量到
                if(YY_bSingStop || (YY_cTotal >= YY_GetSetTotal()) || (YY_FindCanWorkNum() == 0))
                {
                   if(YY_GetLeftSpace() == 0)   
                  {
                      if((YY_cTotal >= YY_GetSetTotal()) || (YY_FindCanWorkNum() == 0))
                      {
                          YY_SetLeftPyData(10,YY_SystemParam->DifferentLengthToothNum);
                          YY_SetRightPyData(10,YY_SystemParam->DifferentLengthToothNum);
                          YY_cStartPYFlag_Left  = 1;
                          YY_cStartPYFlag_Right = 1;
                          YY_cOverTotalRightFlg = 1;
                          YY_cOverTotalLeftFlg  = 1;
                      }
                  }
                    YY_Stop_Action();
                    if(YY_bSingStop == 0)YY_DISPLAY_STATE = 4;     
                }
                YY_RightOk = 0;
                
            }             
        }
        else if(YY_GetRightSpace() > YY_GetRightSpaceDisplay())  //空位状态
        {                       
            if(YY_cStartPYFlag_Right)
            {
                YY_cStartPYFlag_Right = 0;
                if(YY_bDCTEnable)
                {
                    //变为空位，不用铜丝
                    YY_SetRightDCTSpace();           
                }
            }
            
            YY_RightSpaceDisplayAdd();
            
             if(YY_GetRightSpace() == YY_GetRightSpaceDisplay())
             {                            
                YY_SetRightSpaceDisplay(0);
                YY_SetRightDisplay(0);
                YY_cStartPYFlag_Right = 1;
                YY_RightOk = 1;
                if(YY_ChangeNextGroupFlg && YY_LeftOk)
                {
                    YY_ChangeNextGroupFlg = 0;                   
                    YY_LeftOk = 0;
                    YY_RightOk = 0;
                    if(YY_bChangeNextGroup)
                    {
                        YY_bChangeNextGroup = 0;
                        YY_SystemParam->NowGroup = YY_SystemParam->NextGroupBuff - 1;

                        YY_SetLeftPyData(10,YY_SystemParam->DifferentLengthToothNum);
                        YY_SetRightPyData(10,YY_SystemParam->DifferentLengthToothNum);
                        YY_cStartPYFlag_Left  = 1;
                        YY_cStartPYFlag_Right = 1;
                    }
              
                    YY_ChangeGroupControlLeft();  
                }
                

             }

            
        }
        
        
        //如叠牙的情况下，不能送牙
        if((YY_SystemParam->AlarmCode == YY_CHENG_XING_ALARM) || (YY_SystemParam->AlarmCode == YY_TOOTH_NUM_ALARM) || !YY_bDCTEnable)// || M81 || M80)
        {
            YY_SetRightDCTSpace();  
        }
    }
}

void YYa_AutoAction(void)
{  
     YY_Left_Action();
     YY_Right_Action();
}

void YYa_SongLiao(void)
{
    //送丝启动
    if(YY_bSongSi)
    {
        //左送料(送丝)
        if(YY_LEFT_SL_DW_IN)
        {
            YY_LEFT_SL_MOTOR = 1;
        }
        else if(YY_LEFT_SL_UP_IN)
        {
            YY_LEFT_SL_MOTOR = 0;
        }
        //右送料(送丝)
        if(YY_RIGHT_SL_DW_IN)
        {
            YY_RIGHT_SL_MOTOR = 1;
        }
        else if(YY_RIGHT_SL_UP_IN)
        {
            YY_RIGHT_SL_MOTOR = 0;
        }		
    }
    else
    {
        YY_LEFT_SL_MOTOR  = 0;
        YY_RIGHT_SL_MOTOR = 0;
    }
}

// 停止工作
void YY_Stop_Action(void)
{
    YY_bWorkState = 0;   //M7  工作显示
    if((YY_EGMSTOP_IN == 0) && ((YY_SystemParam->AlarmCode & YY_TOOTH_NUM_ALARM) == 0))YY_bZhuYou = 0;  // 注油控制
    YY_bHL = 0;
    YY_bSongSi = 0;
    YY_bPYControl = 0;

    YY_DISPLAY_STATE = 2;
    YY_bRunning = 0;
    YY_bSingStop = 0;
}


//启动时检测当前要加工的组别可不可以加工，不可以就切换到可以加工的组别
unsigned char YY_StartCheckChoose(void)
{
    switch(YY_bMode)
    {
        case YY_SINGLE_MODE:
        {   
            return 1;
        }break;
        case YY_GROUP_MODE:
        {
            if(YY_GroupParam->OverSetTotal[YY_SystemParam->NowGroup] < YY_GroupParam->SetTotal[YY_SystemParam->NowGroup])
            {
                return 1;
            }
            else
            {
                if(YY_FindNextUserFulGroup(YY_SystemParam->NowGroup) != 99)
                {
                    if((YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup] == 0) && (YY_GroupParam->DisplyRightToothNum[YY_SystemParam->NowGroup] == 0))YY_SystemParam->NowGroup = YY_FindNextUserFulGroup(YY_SystemParam->NowGroup);
                    
                    return 1;
                }
                else
                {
                    return 0;
                }
            }
        }break;       
            default:return 0;
    }
}
void YYa_StepCheckStart(void)
{
    if(YY_bFirstZY == 0)//首次加油已经完成
    {
        if((YY_bStart || YY_START_IN_UP) && !YY_bRunning  && YY_bZhuYou && (YY_STOP_IN == 0)  && (YY_SystemParam->AlarmCode== 0) && (YY_StartCheckChoose() == 1)&& (YY_cTotal < YY_GetSetTotal()))
        {
                YY_bWorkState = 1;   //M7  工作显示
                YY_bHL        = 1;   //M4  合链控制
                YY_bSongSi    = 1;  //M5  送丝控制
                YY_bPYControl = 1;  //M6  排牙控制
                YY_bZYNow     = 1;  //M8  马上注油D2时间
                YY_DISPLAY_STATE = 3;
                YY_bRunning = 1; 
  //              YY_DIAPLAY1++;
                if(!YY_bDCTEnable)
                {
                    YY_cStartWorkTime = 3;
                }
        }
        YY_bStart = 0;   //M0   
    }
    else
    {
        YY_bStart = 0;   //M0   
    }
    
    if((YY_cStartWorkTime != 0) && (dwTickCount >= YY_TryDelay))
    {
        YY_cStartWorkTime--;
        YY_SetLeftDCTSpace();
        YY_SetRightDCTSpace();
        YY_TryDelay = dwTickCount + 500;
    }


    //停止
    if(YY_STOP_IN || (YY_bAlarmStop == 1) || YY_bStop)
    {
    //   普通停止是打完当条再停止
        if((YY_bStop || (YY_STOP_IN)) && YY_bDCTEnable)
        {
                if(YY_bPYControl)YY_bSingStop = 1;
        }
        else   //其它故障都要立即停止
        {	
              if(YY_bRunning)YY_ALARM_LED = 1;
              YY_Stop_Action();	
        }
        YY_bStop = 0;   //M0  系统复位
        YY_bAlarmStop = 0;
    }
    
    
}   

//零件寿命相关控制和运算
void YYa_CalParts(void)
{
//    AddUsedLifeControl();

    if(YY_bClearLife1)
    {
        YY_bClearLife1 = 0;
        YY_ComponentParam->LeftRightLife[0] = 0;
        YY_ComponentParam->LeftRightUsedLife[0] = 0;
        
        YY_ComponentParam->RefreshTimes[0]++;
    }
    
    if(YY_bClearTimes1)
    {
        YY_bClearTimes1 = 0;
        YY_ComponentParam->RefreshTimes[0] = 0;
    }
    
    if(YY_bClearLife2)
    {
        YY_bClearLife2 = 0;
        YY_ComponentParam->LeftRightLife[1] = 0;
        YY_ComponentParam->LeftRightUsedLife[1] = 0;
        
        YY_ComponentParam->RefreshTimes[1]++;
    }
    
    if(YY_bClearTimes2)
    {
        YY_bClearTimes2 = 0;
        YY_ComponentParam->RefreshTimes[1] = 0;
    }
    
    if(YY_bClearLife3)
    {
        YY_bClearLife3 = 0;
        YY_ComponentParam->LeftRightLife[2] = 0;
        YY_ComponentParam->LeftRightUsedLife[2] = 0;
        
        YY_ComponentParam->RefreshTimes[2]++;
    }
    
    if(YY_bClearTimes3)
    {
        YY_bClearTimes3 = 0;
        YY_ComponentParam->RefreshTimes[2] = 0;
    }
    
    if(YY_bClearLife4)
    {
        YY_bClearLife4 = 0;
        YY_ComponentParam->LeftRightLife[3] = 0;
        YY_ComponentParam->LeftRightUsedLife[3] = 0;
        
        YY_ComponentParam->RefreshTimes[3]++;
    }
    
    if(YY_bClearTimes4)
    {
        YY_bClearTimes4 = 0;
        YY_ComponentParam->RefreshTimes[3] = 0;
    }
    
    if(YY_bClearLife5)
    {
        YY_bClearLife5 = 0;
        YY_ComponentParam->LeftRightLife[4] = 0;
        YY_ComponentParam->LeftRightUsedLife[4] = 0;
        
        YY_ComponentParam->RefreshTimes[4]++;
    }
    
    if(YY_bClearTimes5)
    {
        YY_bClearTimes5 = 0;
        YY_ComponentParam->RefreshTimes[4] = 0;
    }
    
    if(YY_bClearLife6)
    {
        YY_bClearLife6 = 0;
        YY_ComponentParam->LeftRightLife[5] = 0;
        YY_ComponentParam->LeftRightUsedLife[5] = 0;
        
        YY_ComponentParam->RefreshTimes[5]++;
    }
    
    if(YY_bClearTimes6)
    {
        YY_bClearTimes6 = 0;
        YY_ComponentParam->RefreshTimes[5] = 0;
    }
    
    if(YY_bClearLife7)
    {
        YY_bClearLife7 = 0;
        YY_ComponentParam->LeftRightLife[6] = 0;
        YY_ComponentParam->LeftRightUsedLife[6] = 0;
        
        YY_ComponentParam->RefreshTimes[6]++;
    }
    
    if(YY_bClearTimes7)
    {
        YY_bClearTimes7 = 0;
        YY_ComponentParam->RefreshTimes[6] = 0;
    }
    
    if(YY_bClearLife8)
    {
        YY_bClearLife8 = 0;
        YY_ComponentParam->LeftRightLife[7] = 0;
        YY_ComponentParam->LeftRightUsedLife[7] = 0;
        
        YY_ComponentParam->RefreshTimes[7]++;
    }
    
    if(YY_bClearTimes8)
    {
        YY_bClearTimes8 = 0;
        YY_ComponentParam->RefreshTimes[7] = 0;
    }   
    
    if(YY_bClearLife9)
    {
        YY_bClearLife9 = 0;
        YY_ComponentParam->LeftRightLife[8] = 0;
        YY_ComponentParam->LeftRightUsedLife[8] = 0;
        
        YY_ComponentParam->RefreshTimes[8]++;
    }
    
    if(YY_bClearTimes9)
    {
        YY_bClearTimes9 = 0;
        YY_ComponentParam->RefreshTimes[8] = 0;
    }
    
    if(YY_bClearLife10)
    {
        YY_bClearLife10 = 0;
        YY_ComponentParam->LeftRightLife[9] = 0;
        YY_ComponentParam->LeftRightUsedLife[9] = 0;
        
        YY_ComponentParam->RefreshTimes[9]++;
    }
    
    if(YY_bClearTimes10)
    {
        YY_bClearTimes10 = 0;
        YY_ComponentParam->RefreshTimes[9] = 0;
    }
    
    if(YY_bClearLife11)
    {
        YY_bClearLife11 = 0;
        YY_ComponentParam->LeftRightLife[10] = 0;
        YY_ComponentParam->LeftRightUsedLife[10] = 0;
        
        YY_ComponentParam->RefreshTimes[10]++;
    }
    
    if(YY_bClearTimes11)
    {
        YY_bClearTimes1 = 0;
        YY_ComponentParam->RefreshTimes[10] = 0;
    }
    
    if(YY_bClearLife12)
    {
        YY_bClearLife12 = 0;
        YY_ComponentParam->LeftRightLife[11] = 0;
        YY_ComponentParam->LeftRightUsedLife[11] = 0;
        
        YY_ComponentParam->RefreshTimes[11]++;
    }
    
    if(YY_bClearTimes12)
    {
        YY_bClearTimes12 = 0;
        YY_ComponentParam->RefreshTimes[11] = 0;
    }
    
    if(YY_bClearLife13)
    {
        YY_bClearLife13 = 0;
        YY_ComponentParam->LeftRightLife[12] = 0;
        YY_ComponentParam->LeftRightUsedLife[12] = 0;
        
        YY_ComponentParam->RefreshTimes[12]++;
    }
    
    if(YY_bClearTimes13)
    {
        YY_bClearTimes13 = 0;
        YY_ComponentParam->RefreshTimes[12] = 0;
    }
    
    if(YY_bClearLife14)
    {
        YY_bClearLife14 = 0;
        YY_ComponentParam->LeftRightLife[13] = 0;
        YY_ComponentParam->LeftRightUsedLife[13] = 0;
        
        YY_ComponentParam->RefreshTimes[13]++;
    }
    
    if(YY_bClearTimes14)
    {
        YY_bClearTimes14 = 0;
        YY_ComponentParam->RefreshTimes[13] = 0;
    }
    
    if(YY_bClearLife15)
    {
        YY_bClearLife15 = 0;
        YY_ComponentParam->LeftRightLife[14] = 0;
        YY_ComponentParam->LeftRightUsedLife[14] = 0;
        
        YY_ComponentParam->RefreshTimes[14]++;
    }
    
    if(YY_bClearTimes15)
    {
        YY_bClearTimes15 = 0;
        YY_ComponentParam->RefreshTimes[14] = 0;
    }
    
    if(YY_bClearLife16)
    {
        YY_bClearLife16 = 0;
        YY_ComponentParam->LeftRightLife[15] = 0;
        YY_ComponentParam->LeftRightUsedLife[15] = 0;
        
        YY_ComponentParam->RefreshTimes[15]++;
    }
    
    if(YY_bClearTimes16)
    {
        YY_bClearTimes16 = 0;
        YY_ComponentParam->RefreshTimes[15] = 0;
    }  
}


///////////////////////////////////////////////////////////////////////////////////////////////

void YY_LeftToothDisplayAdd(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:YY_SingleParam->DisplyLeftToothNum++;break;
      case YY_GROUP_MODE:YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup]++;break;
    }   
}

void YY_RightToothDisplayAdd(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:YY_SingleParam->DisplyRightToothNum++;break;
      case YY_GROUP_MODE:YY_GroupParam->DisplyRightToothNum[YY_SystemParam->NowGroup]++;break;
    }   
}

void YY_LeftSpaceDisplayAdd(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:YY_SingleParam->DisplyLeftToothNumSpace++;break;
      case YY_GROUP_MODE:YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup]++;break;
    } 
}

void YY_RightSpaceDisplayAdd(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:YY_SingleParam->DisplyRightToothNumSpace++;break;
      case YY_GROUP_MODE:YY_GroupParam->DisplyRightToothNumSpace[YY_SystemParam->NowGroup]++;break;
    } 
}

unsigned long YY_GetLeftToothNum(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          return  YY_SingleParam->LeftToothNum;
      }break;
      case YY_GROUP_MODE:
      {
          return YY_GroupParam->LeftToothNum[YY_SystemParam->NowGroup];
      }break;
      default:return 0;
    }   
}

unsigned long YY_GetRightToothNum(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          return  YY_SingleParam->RightToothNum;
      }break;
      case YY_GROUP_MODE:
      {
          return YY_GroupParam->LeftToothNum[YY_SystemParam->NowGroup];
      }break;
      default:return 0;
    }   
}

unsigned long YY_GetLeftToothNumDisplay(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          return  YY_SingleParam->DisplyLeftToothNum;
      }break;
      case YY_GROUP_MODE:
      {
          return YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup];
      }break;
      default:return 0;
    }  
}

unsigned long YY_GetRightToothNumDisplay(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          return  YY_SingleParam->DisplyRightToothNum;
      }break;
      case YY_GROUP_MODE:
      {
          return YY_GroupParam->DisplyRightToothNum[YY_SystemParam->NowGroup];
      }break;
      default:return 0;
    }  
}

unsigned long YY_GetLeftSpace(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          return  YY_SingleParam->LeftToothNumSpace;
      }break;
      case YY_GROUP_MODE:
      {
          return YY_GroupParam->LeftToothNumSpace[YY_SystemParam->NowGroup];
      }break;
      default:return 0;
    }  
}

unsigned long YY_GetRightSpace(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          return  YY_SingleParam->RightToothNumSpace;
      }break;
      case YY_GROUP_MODE:
      {
          return YY_GroupParam->LeftToothNumSpace[YY_SystemParam->NowGroup];
      }break;
      default:return 0;
    }  
}

unsigned long YY_GetLeftSpaceDisplay(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          return  YY_SingleParam->DisplyLeftToothNumSpace;
      }break;
      case YY_GROUP_MODE:
      {
          return YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup];
      }break;
      default:return 0;
    }  
}

unsigned long YY_GetRightSpaceDisplay(void)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          return  YY_SingleParam->DisplyRightToothNumSpace;
      }break;
      case YY_GROUP_MODE:
      {
          return YY_GroupParam->DisplyRightToothNumSpace[YY_SystemParam->NowGroup];
      }break;
      default:return 0;
    }  
}

void YY_SetLeftDCTSpace(void)
{
    //变为空位，不用铜丝
    YY_LEFT_OUT = 0;
    YY_LEFT_IN  = 1; 
    YY_LCntDelay = dwTickCount + YY_DCT_OUT_TIME;  
}

void YY_SetLeftDCTTooth(void)
{
    //变为排牙
    YY_LEFT_OUT = 1;
    YY_LEFT_IN  = 0; 
    YY_LCntDelay = dwTickCount + YY_DCT_OUT_TIME;  
}

void YY_SetRightDCTSpace(void)
{
    //变为空位，不用铜丝
    YY_RIGHT_OUT = 0;
    YY_RIGHT_IN  = 1; 
    YY_RCntDelay = dwTickCount + YY_DCT_OUT_TIME;
}

void YY_SetRightDCTTooth(void)
{
    //变为排牙
    YY_RIGHT_OUT = 1;
    YY_RIGHT_IN  = 0; 
    YY_RCntDelay = dwTickCount + YY_DCT_OUT_TIME;  
}


void YY_SetLeftPyData(unsigned short cLeftData,unsigned short cLeftKongWei)
{
    YY_NowLeftPyKongWei = cLeftKongWei;
    YY_NowLeftPyNum     = cLeftData;
}

void YY_SetRightPyData(unsigned short cRightData,unsigned short cRightKongWei)
{
    YY_NowRightPyKongWei = cRightKongWei;
    YY_NowRightPyNum     = cRightData;
}

void YY_SetLeftDisplay(unsigned short source_data)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          YY_SingleParam->DisplyLeftToothNum = source_data;
      }break;
      case YY_GROUP_MODE:
      {
          YY_GroupParam->DisplyLeftToothNum[YY_SystemParam->NowGroup] = source_data;
      }break;
    }    
}

void YY_SetRightDisplay(unsigned short source_data)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
          YY_SingleParam->DisplyRightToothNum = source_data;
      }break;
      case YY_GROUP_MODE:
      {
          YY_GroupParam->DisplyRightToothNum[YY_SystemParam->NowGroup] = source_data;
      }break;
    }    
}

void YY_SetLeftSpaceDisplay(unsigned short source_data)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
           YY_SingleParam->DisplyLeftToothNumSpace = source_data;
      }break;
      case YY_GROUP_MODE:
      {
          YY_GroupParam->DisplyLeftToothNumSpace[YY_SystemParam->NowGroup] = source_data;
      }break;
    }    
}

void YY_SetRightSpaceDisplay(unsigned short source_data)
{
    switch(YY_bMode)
    {
      case YY_SINGLE_MODE:
      {
           YY_SingleParam->DisplyRightToothNumSpace = source_data;
      }break;
      case YY_GROUP_MODE:
      {
          YY_GroupParam->DisplyRightToothNumSpace[YY_SystemParam->NowGroup] = source_data;
      }break;
    }    
}


unsigned long YY_GetTotal(void)
{
    switch(YY_bMode)
    {
        case YY_SINGLE_MODE:
        {
             return YY_SingleParam->OverTotal;
        }break;
        case YY_GROUP_MODE:
        {
             return YY_GroupParam->AllOverTotal;
        }break;
        default:return 0;
    }
}

unsigned long YY_GetSetTotal(void)
{
   switch(YY_bMode)
  {
      case YY_SINGLE_MODE:return YY_SingleParam->SetTotal;break;
      case YY_GROUP_MODE:return YY_GroupParam->AllSetTotal;break;  
      default:return 0;
  }
}

void YY_AddTotal(void)
{
   switch(YY_bMode)
  {
      case YY_SINGLE_MODE:YY_SingleParam->OverTotal++;break;
      case YY_GROUP_MODE:
      {
          YY_GroupParam->AllOverTotal++;
          YY_GroupParam->OverSetTotal[YY_SystemParam->NowGroup]++;
      }break;  
  }
}

//算单个齿长度
float YY_CalToothLength(unsigned short roll_diameter,unsigned short tooth_num)
{
    float buff,buff_num;
    
    buff = roll_diameter;
    buff_num = tooth_num;
    return (buff * 3.1415926 / buff_num);
}


//输入齿数计算长度返回的是单位厘米
unsigned long YY_ToothNumCalLengthCM(float single_length,unsigned short tooth_num,unsigned long zipper_num)
{
    float buff1,buff2,buff3;
    buff1 = single_length;
    buff2 = tooth_num;
    buff3 = zipper_num;    
    return (unsigned long)(buff1 * buff2 * buff3);
}

//输入齿数计算长度返回的是单位英寸
unsigned long YY_ToothNumCalLengthInch(float single_length,unsigned short tooth_num,unsigned long zipper_num)
{
    float buff1,buff2,buff3;
    buff1 = single_length;
    buff2 = tooth_num;
    buff3 = zipper_num;
    return (unsigned long)(buff1 * buff2 * buff3 / 2.5399);
}

//输入长度厘米算齿数
unsigned long YY_ToothLengthCMCalNum(float single_length,unsigned short tooth_length,unsigned long zipper_num)
{
     float buff1,buff2,buff3;
    buff1 = zipper_num;
    buff2 = tooth_length;
    buff3 = single_length;  
    return (unsigned long)ceil(buff1 * buff2 / buff3);
}

//输入长度厘米算英寸
unsigned long YY_ToothLengthCMCalInch(float single_length,unsigned short tooth_length,unsigned long zipper_num)
{
    float buff1,buff2;
    buff1 = tooth_length;
    buff2 = zipper_num;

    return (unsigned long)(buff1 * buff2 / 2.5399);
}



//输入厘米长度计算总长度单位米
unsigned long YY_LengthCalLengthM(unsigned short set_length,unsigned short kongwei_length,unsigned long zipper_num)
{
    float buff1,buff2,buff3;
    
    buff1 = set_length;
    buff2 = kongwei_length;
    buff3 = zipper_num;
    return (unsigned long)((buff1 + buff2) * buff3 / 100);
}
//输入英寸长度计算总长度
unsigned long YY_InchLengthCalLength(unsigned short set_length,unsigned short kongwei_length,unsigned long zipper_num)
{
    float buff1,buff2,buff3;
    
    buff1 = set_length;
    buff2 = kongwei_length;
    buff3 = zipper_num;
    return (unsigned long)((buff1 + buff2) * buff3 / 2.5399);
}

//输入齿数计算长度返回的是单位米
unsigned long YY_ToothNumCalLength(float single_length,unsigned short tooth_num,unsigned long zipper_num)
{
    float buff1,buff2,buff3;
    
    buff1 = single_length;
    buff2 = tooth_num;
    buff3 = zipper_num;
    return (unsigned long)(buff1 * buff2 * buff3 / 1000);
}

//输入齿数计算长度返回的是单位米带浮点型
float YY_ToothNumCalLengthFloat(float single_length,unsigned short tooth_num,unsigned long zipper_num)
{
    float buff1,buff2,buff3;
    
    buff1 = single_length;
    buff2 = tooth_num;
    buff3 = zipper_num;
    return (buff1 * buff2 * buff3 / 1000);
}

//输入长度英寸算齿数
unsigned long YY_ToothLengthInchCalNum(float single_length,unsigned short tooth_length,unsigned long zipper_num)
{
    float buff1,buff2;
    buff1  = zipper_num * tooth_length;
    buff2  = single_length; 
    return (unsigned long)ceil(buff1  * 2.5399 / buff2);
}

//输入长度英寸算厘米
unsigned long YY_ToothLengthInchCalCM(float single_length,unsigned short tooth_length,unsigned long zipper_num)
{  
    float buff1,buff2;
    buff1 = tooth_length;
    buff2 = zipper_num;
    return (unsigned long)(buff1 * buff2  * 2.5399);
}
#endif