GC23005/Machine/FeiYueMachine/ian.h

#if FIE_YUE_MACHINE==1

extern void XYChuanTou_HeLian_InitAction(void);
extern void XYChuanTou_HeLian_Action(void);
extern void XYChuanTou_HeLian_SetAlarmCode(unsigned alarm_code);
extern void ExtiAcitionX02(void);

#define DIR_P 1
#define DIR_N 0

#define MOTOR_EN 0
#define MOTOR_DISEN 1

#define MOTOR_ALARM 0
#define MOTOR_NOALARM 1

#define CTHL_VAVLE_ERROR_TIME   3000 
#define CTHL_MOTOR_ALARM_TIME   5000


//故障代码列表
#define CTHL_NO_ALARM                0
#define CTHL_WLZDTJ_ALARM            1   //无拉链自动停机
#define CTHL_XKSC_Limit_ALARM        2   //X03斜口上止到位异常
#define CTHL_TLiao_Limit_ALARM       3   //X04推料到位异常

#define CTHL_HSLiao_Limit_ALARM      5   //X06横送料到位异常
#define CTHL_HSLiao_Origin_ALARM     6   //X07横送料原位异常
#define CTHL_JLiao_Limit_ALARM       7   //X10接料到位异常
#define CTHL_CTM_Limit_ALARM         8   //X11穿头模到位异常
#define CTHL_CTM_Origin_ALARM        9   //X12穿头模原位异常
#define CTHL_First_CT_Origin_ALARM   10  //X13一次穿头原位异常
#define CTHL_LTou_Check_ALARM        11   //X14拉头缺料感应异常
#define CTHL_DK_ERROR_ALARM        12   //没有检测到方块
#define CTHL_CX_Limit_ALARM          13   //X16插稍到位感应异常
#define CTHL_XKTD_Origin_ALARM       14   //X17斜口原位感应异常
#define CTHL_CXLimit_ALARM        15   //X20插稍下移到位异常
#define CTHL_SF_ALR_ALARM            16   //X22伺服报警异常
#define CTHL_SF_Origin_ALARM         17   //X23伺服原位(穿链原位)异常
#define CTHL_ZLT_ALARM               18   //装拉头异常
#define CTHL_FK_Check_ALARM          19   //X02方块检测
#define CTHL_FKCXDW_ALARM            20   //方块插销定位异常警告
#define CTHL_YCCRYWYC_ALARM          21   //一次穿入原位异常
#define CTHL_XCXXCYC_ALARM           22   //小插销行程异常
#define CTHL_HENSONGLIAO_ALARM       23   //横送料不能输出
#define CTHL_YCCT_ALARM              24   //一次穿头不能输出
#define CTHL_YCXM_Origin_ALARM       25   //一次穿头和下模不能输出
#define CTHL_DXKCTXM_Origin_ALARM    26   //顶斜口和穿头下模不能输出
#define CTHL_XKTD_ALARM              27   //斜口推带不能有输出
#define CTHL_CXQJD_ALARM             28   //插销前夹带不能有输出
#define CTHL_WFZIDONGCX_ALARM         29   //无法自动插销
#define CTHL_SafeDoor_ALARM           30    //安全门关上才能启动

#define CTHL_AutoStep            cStepMByte
#define CTHL_ZhuangLiaoStep      cStepMByte1
#define CTHL_TLiaoStep           cStepMByte2
#define CTHL_TD_MotorStep        cStepMByte3     //拖带电机
#define CTHL_JiaLianStep         cStepMByte4
#define CTHL_ZhenDongStep        cStepMByte6
#define CTHL_SongLiaoStep        cStepMByte7
#define CTHL_CL_MotorStep        cStepMByte8     //穿链
#define CTHL_AutoStep1           cStepMByte9

#define CTHL_bFKCXTDDW_Step      cStepMByte10    
#define CTHL_bCXCR_Step          cStepMByte11
#define CTHL_bCLFirst_Step       cStepMByte12


#define CTHL_ZhuangLiaoDelay      cDelayTime2
#define CTHL_TLiao_Delay          cDelayTime3
#define CTHL_TD_MotorDelay        cDelayTime4
#define CTHL_AutoDelay            cDelayTime5
#define CTHL_TestDelay            cDelayTime6
#define CTHL_CL_MotorDelay        cDelayTime7
#define CTHL_TouchDelay           cDelayTime8
#define CTHL_AutoDelay1           cDelayTime9
#define CTHL_ZDP_Delay            cDelayTime10
#define CTHL_bCXCR_Delay          cDelayTime11
#define CTHL_bFKCXTDDW_Delay      cDelayTime12
#define CTHL_bCLFirst_Delay      cDelayTime13
#define CTHL_bLTCHECK_Delay      cDelayTime14
#define CTHL_bSFBBAOJIN_Delay      cDelayTime15
//32位无符号变量
#define CTHL_LianLengthCheck     cUDword32Buff1
#define CTHL_LianLengthAutoCheck cUDword32Buff2
#define CTHL_LianLengthReal          cUDword32Buff3
#define CTHL_LianLengSave          cUDword32Buff8
#define CTHL_LianLengthAutoCheckERROR  cUDword32Buff5
#define CTHL_LianLengthCheckOLD               cUDword32Buff6
#define CTHL_LianLengthNEWCheck               cUDword32Buff7

//32位有符号变量
#define CTHL_XSavePosBuff        cDword32Buff1
#define CTHL_X_CXPosBuff         cDword32Buff2
#define CTHL_YSavePosBuff        cDword32Buff3
#define CTHL_CheckInX02PosBuff   cDword32Buff4
#define CTHL_YsaveCXDWPosBuff   cDword32Buff5
#define CTHL_LENTH              cDword32Buff6
#define CTHL_Y_CL_Length        cDword32Buff7
#define CTHL_Y_CL_PosBuff        cDword32Buff8



//8位变量
#define CTHL_TryCnt              cCharBuff1
#define cZipCnt                     cCharBuff2
#define cStopInCnt                  cCharBuff3
#define cStopMode                   cCharBuff4
#define cXcxcrCnt                   cCharBuff5
#define cWULATOUCnt                   cCharBuff6
#define cQDXK_DXK                   cCharBuff7
#define cZDP_Auto                   cCharBuff8
#define cXCXQXQD                    cCharBuff9
#define cXiaoChaCNT                    cCharBuff10
#define cBAOHUCNT                   cCharBuff11
#define cCHULIANBAOJIN               cCharBuff12
#define cHeLian                        cCharBuff13
//位标志位
#define bTuiLaTouOkFlg              bBitFlag0
#define bZhuangLiaoOkFlg            bBitFlag1
#define bXiaMoENFlg                 bBitFlag2
#define bYFirstDingWeiFlg           bBitFlag3
#define bCL_EN_FLG                  bBitFlag4
#define bCL_OK_FLG                  bBitFlag5
#define bCheckEN_FLG                bBitFlag6
#define bSingOneFlg                 bBitFlag7  

#define CTHL_TOTAL_ADDR  76

#define CTHL_SPEED_ADDR     78
#define CTHL_ALARM_ADDR     100
#define CTHL_TRUST_ALARM_ADDR     102
#define CTHL_TEST_ALARM_ADDR       106

#define CTHL_PARAM_CYCLE_PULSE       user_datas[0]//0 转一圈脉冲数  
#define CTHL_PARAM_CYCLE_LENGTH      user_datas[1]//整数 转一圈拖带多长 
#define CTHL_PARAM_TD_RunSpeed       user_datas[2]//整数 拖带电机拖带速度
#define CTHL_PARAM_FKDW_Speed        user_datas[3]//整数 方块定位速度(低速度)
#define CTHL_PARAM_CL_Speed          user_datas[4]//整数 合链速度
#define CTHL_PARAM_CL_Back_O_Speed   user_datas[5]//整数 合链电机回零速度
#define CTHL_PARAM_FKDW_Length       user_datas[6]//0.01 方块定位长度
#define CTHL_PARAM_CXDW_Length       user_datas[7]//0.01 插销定位长度
#define CTHL_PARAM_CL_Length         user_datas[8]//0.01 合链长度
#define CTHL_PARAM_CL_MAX_Length     user_datas[9]//0.01 穿链最长限制

#define CTHL_PARAM_TLiao_BACKDELAY   (10*user_datas[10])//0.01推拉头到位延时返回
#define CTHL_PARAM_MaGou_DELAY       (10*user_datas[11])//0.01接料到位延时码勾
#define CTHL_PARAM_HSLiaoOff_DELAY   (10*user_datas[12])//0.01码勾输出后退横送料
#define CTHL_PARAM_CheckLT_DELAY     (10*user_datas[13])//0.01码勾输出后延时检测拉头
#define CTHL_PARAM_SCDWOff_CXDW_DELAY (10*user_datas[14])//0.01退上止定位延时穿插销
#define CTHL_PARAM_First_CL_Timer     (10*user_datas[15])    //0.01一次穿入时间
#define CTHL_PARAM_MGOff_XiaMo_DELAY (10*user_datas[16])     //0.01松码勾后延时退下模
#define CTHL_PARAM_CXCR_DELAY        (10*user_datas[17])    //0.01插销延时穿入
#define CTHL_PARAM_XKDW_TD_DELAY        (10*user_datas[18])    //0.01斜口定位后延时拖带
#define CTHL_PARAM_XK_CR_DELAY        (10*user_datas[19])    //0.01斜口延时穿拉头
#define CTHL_PARAM_DXK_XKDW_Off_DELAY (10*user_datas[20])    //0.01顶斜口后延时退斜口定位
#define CTHL_PARAM_XCQJD_XCDW_DELAY      (10*user_datas[21])    //0.01插销前夹带后延时插销定位
#define CTHL_PARAM_First_CL_DELAY        (10*user_datas[22])    //0.01延时一次穿入
#define CTHL_PARAM_HLJJ_CL_DELAY        (10*user_datas[23])    //0.01合链夹具延时穿入   
#define CTHL_PARAM_ZDP_Start_TIME      (10*user_datas[24])      //0.01振动盘启动延时  
#define CTHL_PARAM_ZDP_Stop_TIME       (10*user_datas[25])       //0.01振动盘延时停止 
#define CTHL_PARAM_XCX_LENTH           user_datas[26]       //0.01 小插销感应后再走标准长度 
#define CTHL_PARAM_XCXWC_LENTH          user_datas[27]       //0.01 小插销标准长度过长的误差值 
#define CTHL_PARAM_TDFZ_LENTH          user_datas[28]       //0.01拖带电机反转长度
#define CTHL_PARAM_WLCDSHEZHI_LENTH   (10* user_datas[29])       //0.1无拉链情况再走长度设置
#define CTHL_PARAM_DXKFZ_LENTH         user_datas[30]       //顶斜口反转长度
#define CTHL_PARAM_DXKYS_DELAY         (user_datas[31]*10)  //前顶斜口后延时顶斜口
#define CTHL_PARAM_ZDP_AUTO                  user_datas[32]
#define CTHL_PARAM_TDCR_LowSpeed             user_datas[33] //拖带穿入慢速
#define CTHL_PARAM_TDCR_LowSpeedLength       user_datas[34] //拖带穿入慢速距离
#define CTHL_PARAM_FKJD_DELAY                  (user_datas[35]*10) //定位延时方块夹带
#define CTHL_PARAM_FKGD_DELAY                  (user_datas[36]*10)  //延时退方块固定

#define CTHL_PARAM_AUTO_MODE            user_datas[37] //手动/自动合链
#define CTHL_PARAM_NLSL_MODE                       user_datas[39] //尼龙塑料切换 0塑料/1尼龙
#define CTHL_PARAM_HLTSY_LENTH                       user_datas[40]  //合拉头剩余长度
#define CTHL_PARAM_CXMODE                   user_datas[41]  //下移/直插
#define CTHL_PARAM_FKJDSECONG_DEALY              (user_datas[42]*10) //拖带时候延时方块夹带
#define CTHL_PARAM_WUCD_LENTH              user_datas[43]//拖带时候延时方块夹带
#define CTHL_PARAM_DB_MODE             0//user_datas[44] //伺服报警  0为DB ，1为IO
#define CTHL_PARAM_SF_MODE              user_datas[45]//0伺服电机  1步进电机
//输入

#define CTHL_START_IN            M0384 //X00  //启动
#define CTHL_START_IN_UP         (M0384 && !OLDM384)//(X00 && !OLDX00)
#define CTHL_STOP_IN             M0385 // X01  //停止
#define CTHL_STOP_IN_UP          (M0385 && !OLDM385)//(X01 && !OLDX01)
#define CTHL_STOP_IN_DW          (!M0385 && OLDM385)//(!X01 && OLDX01)
#define CTHL_FK_Check            M0386   //X02方块检测
#define CTHL_FK_Check_UP          (M0386 && !OLDM386)
#define CTHL_FK_Check_DW          (!M0386 && OLDM386)
#define CTHL_XKSC_Limit_IN       M0387   //X03斜口上止到位
#define CTHL_TLiao_Limit_IN      M0388   //X04推料到位
#define CTHL_SafeDoor_IN         M0389   //X05安全门
#define CTHL_HSLiao_Limit_IN     M0390   //X06横送料到位
#define CTHL_HSLiao_Origin_IN    M0391   //X07横送料原位
#define CTHL_JLiao_Limit_IN      M0392   //X10接料到位
#define CTHL_CTM_Limit_IN        M0393   //X11穿头模到位
#define CTHL_CTM_Origin_IN       M0394   //X12穿头模原位
#define CTHL_First_CT_Origin_IN  M0395   //X13一次穿头原位
#define CTHL_LTou_Check          M0396   //X14拉头缺料感应
#define CTHL_CXSC_Limit_IN       M0397   //X15插稍上止感应
#define CTHL_CXSC_Limit_IN_UP    (M0397 && !OLDM397)
#define CTHL_CXSC_Limit_IN_DW    (!M0397 && OLDM397)
#define CTHL_CX_Limit_IN         M0398   //X16插稍到位感应
#define CTHL_XKTD_Origin_IN      M0399   //X17斜口推带原位感应
#define CTHL_CXLimit_IN       M0400   //X20插稍下移到位
#define CTHL_ZDP_IN              M0401   //X21振动盘
#define CTHL_SF_ALR_IN           M0402   //X22伺服报警
#define CTHL_SF_Origin_IN        M0403   //X23伺服原位(穿链原位)


//输出
#define CTHL_TLiao_VAVLE        M0304  //Y00 推料电磁阀              
#define CTHL_HSLiao_VAVLE       M0305  //Y01 横送料电磁阀
#define CTHL_JLTou_VAVLE        M0306  //Y02 接拉头电磁阀
#define CTHL_XKTD_VAVLE         M0307  //Y03 斜口推带电磁阀
#define CTHL_XKDW_VAVLE         M0308  //Y04 斜口定位电磁阀
#define CTHL_DXK_VAVLE          M0309  //Y05 顶斜口电磁阀
#define CTHL_CXVAVLE         M0310  //Y06 插销下移电磁阀
#define CTHL_CTXM_VAVLE         M0311  //Y07 穿头下模电磁阀
#define CTHL_First_CT_VAVLE     M0312  //Y10 一次穿头电磁阀
#define CTHL_FKGD_VAVLE         M0313  //Y11 方块固定电磁阀
#define CTHL_CXQJD_VAVLE        M0314  //Y12 插销前夹带电磁阀
#define CTHL_CXDWZ_VAVLE        M0315  //Y13 插销定位针(到位)电磁阀
#define CTHL_CXHJD_VAVLE        M0316  //Y14 插销后夹带电磁阀
#define CTHL_CXHDW_VAVLE        M0317  //Y15 插销后定位电磁阀
#define CTHL_FKJD_VAVLE         M0318  //Y16 方块夹带电磁阀
#define CTHL_ZhenDongPian_OUT   M0319  //Y17 振动盘启动吹气电磁阀
#define CTHL_HLJJ_VAVLE         M0320  //Y20 合链夹具电磁阀
#define CTHL_CXSCDW_VAVLE       M0321   //Y21 插销上止定位电磁阀

#define CTHL_MGuo_VAVLE         M0323   //Y23 码勾电磁阀


#define CTHL_SF_ALR_CLR         M0324  //Y24 伺服警告清除
#define CTHL_Run_State          M0325   //Y25 运行灯
#define CTHL_Stop_State         M0326   //Y26 停止灯
#define CTHL_QDXK_VAVLE         M0327   // Y27 前顶斜口电磁阀

#define CTHL_TestLED             M0328   //Y30 测试状态灯


//M0~M4全局固定使用
/*
#define bRunning                    M0000
#define bStart                      M0001
#define bStop                       M0002
#define bAlarmStop                  M0003
#define bClearTotal                 M0004
*/
#define CTHL_bTLiao          M0005      //手动推料
#define CTHL_bHSL            M0006      //手动横送料     
#define CTHL_bJLT            M0007       //接拉头
#define CTHL_bMG             M0008       //码勾
#define CTHL_bFKJD           M0009       //方块夹带
#define CTHL_bXKTD           M0010       //斜口推带
#define CTHL_bXKDW           M0011       //斜口定位
#define CTHL_bCTXM           M0012       //穿头下模
#define CTHL_bDXK            M0013       //顶斜口
#define CTHL_bFKGD           M0014       //方块固定
#define CTHL_bCXQJD          M0015       //插销前夹带
#define CTHL_bCXSY           M0016       //插销上移电磁阀
#define CTHL_bCXDWZ          M0017       //Y14 插销定位针电磁阀
#define CTHL_bCXHJD          M0018       //Y15 插销后夹带电磁阀
#define CTHL_bCXHDW          M0019       //Y16 插销后定位电磁阀
//#define CTHL_bCXDWCheck      M0020       //Y17 插销到位电磁阀
#define CTHL_bFirst_CT       M0021       //Y20 一次穿头电磁阀
#define CTHL_bHLJJ           M0022       //Y21 合链夹具电磁阀
#define CTHL_bCXSCDW         M0023       //Y23 插销上止定位电磁阀

#define CTHL_bCLMotor_P      M0026       //穿链电机正转
#define CTHL_bCLMotor_N      M0025       //穿链电机反转
//下面为动作组合按键
#define CTHL_bAutoZhuangLiao M0024       //自动装料
#define CTHL_bCLMotor_O      M0027       //穿链电机定位原点
#define CTHL_bCL_First       M0028       //一次穿链动作
#define CTHL_bFKTDDW         M0029       //拖带方块定位
#define CTHL_bFKCXTDDW       M0030       //拖带方块插销定位
#define CTHL_bCXMotorDW      M0031       //插销电机前定位
#define CTHL_bCXCR           M0032       //插销穿入(包含电机前定位,插销下移,后夹,后定位)
#define CTHL_bMotorHL        M0033       //电机合链操作
#define CTHL_bQianDXK        M0034       //Y27 前顶斜口电磁阀
#define CTHL_bQianDXK_DXK    M0035       //顶斜口动作
//#define CTHL_bCloseAuto       M0036       //关闭自动振动盘
#endif